I love play with this borad but all of a suden the i96 will not boot with a message like this.
RDA8810 Boot_ROM V1.6
HW_CFG: 1286
SW_CFG: 0000
Load EMMC
Open eMMC
EMMC OCR timeout
Open eMMC card Failed
Load EMMC Fail
Load SD
Open SD card
mcd_Open
Card is SDHC
Inserted Card is a SD card
mcd_Open Done
Loading image from SD card …Done
Check Image … Done
Run …
Init Clock …
Clock config ver: 1.0
PMU vbuck1 = 9, vbuck3 = 10
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
rda2 stand for dqs_prsel_preset
rda2=0 rda2=1 rda2=2 rda2=3 rda2=4 rda2=5 rda2=6 rda2=7
R R R R * * R R
Please check the result and choose the best one
final rda2= 0, rda2_old = 2
setup ddr vtt to 1
pll freq CPU = 988
pll freq BUS = 800
pll freq MEM = 260
Init DDR, flag = 0x0002, para = 0x00001338
32bit dll-on Mode …
ddr2 phy init done!
format ctrl value: 22000202
address ctrl value: 30301
decode ctrl value: 10
dram init done …
Done
SETTING SECURITY CONTEXT
Board security: Not present
Init emmc …
MMC: registered mmc interface 0
Spl init emmc first, use default zero mclk adj and inv.
MMC: registered mmc interface 1
raise: Signal # 8 caught
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x0010fd48
-------------MMC information-----------
Manufacturer ID: 89, Name: Unknown
OEM: 303
Tran Speed: 25000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: Bus Width: 4-bit
boot_mmc mfr id = 89
EMMC boot …
Check Image …Verify image:
Done
U-Boot 2012.04.442-rel5.0.2 (Oct 24 2022 - 17:31:16)
RDA8810 SoC
Board: RDA8810
DRAM: 236 MiB
CPU: enable instruction caches
CPU: enable data caches
CPU: enable neon
CPU: p15-c1-c1 (NSACR): 0x00000000 → 0x00000c00
CPU: p15-c1-c0 (CPACR): 0x00000000 → 0x00f00000
NAND: metal 28 hwcfg 1286, use eMMC, skip nand init
0 MiB
MMC: MMC: registered mmc interface 0
Cannot find the emmc corresponding mclk adj and inv.Now use default zero. Please add it
MMC: registered mmc interface 1
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8dae5e88
-------------MMC information-----------
Manufacturer ID: 89, Name: Unknown
OEM: 303
Tran Speed: 25000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: Bus Width: 4-bit
MMC: 0, MMC: 1
Using default environment
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
#-------Board Mux config found error-------#
Some used GPIO A are not available (0x8003)
#-------Board Mux config found error-------#
Some used GPIO D are not available (0x4)
Board Mux : Error.
mmc0 is current device
Loading file “boot.scr” from mmc device 0:1 (xxa1)
884 bytes read
Executing script at 81000000
** No boot file defined **
Loading file “uInitrd” from mmc device 0:1 (xxa1)
3091319 bytes read
Loading file “zImage” from mmc device 0:1 (xxa1)
4022560 bytes read
Loading file “modem.bin” from mmc device 0:1 (xxa1)
2097152 bytes read
Checking Modem Code Image at 82000000 …
Verifying Image Header … OK
Image Name: Modem raminit codes
Image Type: MIPS Linux Kernel Image (uncompressed)
Data Size: 2064 Bytes = 2 KiB
Load Address: 01c16000
Entry Point: 81c16000
Verifying Data Checksum … OK
Raminit Image Detected
Checking Modem Code Image at 82000850 …
Verifying Image Header … OK
Image Name: Modem work codes
Image Type: MIPS Linux Kernel Image (uncompressed)
Data Size: 2003744 Bytes = 1.9 MiB
Load Address: 02000800
Entry Point: 82000800
Verifying Data Checksum … OK
Work Image Detected
Set modem logic base address 0x2000000
Init mdcom ports … Done
Load Raminit Code to modem at 01c16000 (AP address 11c16000) …
pc = 81c16000
param = 00000000
Done
Start modem and waiting for response … Done
Load Work Code to modem at 02000800 (AP address 12000800) …
pc = 82000800
param = 00000000
Done
Load Calib Data to modem at Load factory from flash …
lba size = 512
lba_start partition_size name
========= ====================== ==============
4096 52428800( 50M) xxa1
106496 1103101952( 1052M) xxa2
========= ====================== ==============
mmc partition table doesn’t existLoad Failed
MOMEM EXT CALIB address 123f8000 …
Factory already loaded
MOMEM CALIB address 123fc000 …
Factory already loaded
MOMEM FACT address 123fe000 …
Factory already loaded
AP FACT address 123ff000 …
Start modem …
Waiting for modem response … Done
Reset cause : 0x00000000
Communication interface version : 0x00010001
Power-on key is not pressed for normal boot.
****** Shutdown is needed later ******
Init mdcom channels … Done
Loading init Ramdisk from Legacy Image at 85000000 …
Image Name: uInitrd
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 3091255 Bytes = 2.9 MiB
Load Address: 00000000
Entry Point: 00000000
Starting kernel …
Uncompressing Linux…
Then it gets stuck at this point
I burn the images for the orangepi.org and used muiltipy sd cards not sure how to fix this issuse please help.
