LinkSprite Mezzanine Card, Can't load OS


#1

I receiver a LinkSprite Mezzanine card from Arrow (http://linksprite.com/wiki/index.php5?title=Linker_Mezzanine_card_starter_kit_for_96board), and I decided to try the sliding Rheostat project. Following the steps I plugged the Rheostat to the mezzanine card with the included cable. I then mounted the mezzanine card onto the 410c using the included standoffs and screws (fits perfectly, great job). Next I flipped to the Program tab and noticed that this is a Linux program, no problem I’ll install Linux on the 410c. I flipped dipswitch 2 (SD Boot), and inserted the SDCard with the latest Debian image and applied power.

Now is when the trouble started: The 410c boots, displays the installer menu for about 5 seconds, then reboots. This loop continues forever. Removing the LinkSprite card allows the system to boot and I installed Debian. I couldn’t install Debian from SDCard while the LinkSprite card was attached.

After Debian is running, I powered down, re-attached the LinkSprite mezzanine board, and rebooted. The 410c comes up and runs fine. My question is, what signal is the mezzanine card toggling on the low-speed connector that prevents the installer from running?

Here is the console output:


Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.0-00261
S - IMAGE_VARIANT_STRING=HAAAANAAA
S - OEM_IMAGE_VERSION_STRING=C-BPATTH
S - Boot Config, 0x000002e3
S - Core 0 Frequency, 0 MHz
B -      1544 - PBL, Start
B -      3488 - bootable_media_detect_entry, Start
B -    128973 - bootable_media_detect_success, Start
B -    128977 - elf_loader_entry, Start
B -    131534 - auth_hash_seg_entry, Start
B -    131744 - auth_hash_seg_exit, Start
B -    159376 - elf_segs_hash_verify_entry, Start
B -    218247 - PBL, End
B -    183183 - SBL1, Start
B -    234453 - pm_device_init, Start
D -     14274 - pm_device_init, Delta
B -    249215 - boot_flash_init, Start
D -         0 - boot_flash_init, Delta
B -    253241 - boot_config_data_table_init, Start
D -    429531 - boot_config_data_table_init, Delta - (0 Bytes)
B -    687317 - CDT version:3,Platform ID:24,Major ID:1,Minor ID:0,Subtype:0
B -    693539 - sbl1_ddr_set_params, Start
B -    697230 - cpr_init, Start
D -         0 - cpr_init, Delta
B -    702842 - Pre_DDR_clock_init, Start
D -       183 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta
B -    715347 - pm_driver_init, Start
D -     10034 - pm_driver_init, Delta
B -    734043 - clock_init, Start
D -        61 - clock_init, Delta
B -    744169 - Image Load, Start
D -     33306 - QSEE Image Loaded, Delta - (460664 Bytes)
B -    777506 - Image Load, Start
D -      1220 - SEC Image Loaded, Delta - (2048 Bytes)
B -    784643 - sbl1_efs_handle_cookies, Start
D -         0 - sbl1_efs_handle_cookies, Delta
B -    792542 - Image Load, Start
D -     13206 - QHEE Image Loaded, Delta - (51952 Bytes)
B -    805749 - Image Load, Start
D -     17202 - RPM Image Loaded, Delta - (149492 Bytes)
B -    822981 - Image Load, Start
D -     22753 - APPSBL Image Loaded, Delta - (479072 Bytes)
B -    845765 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -    851468 - SBL1, End
D -    670634 - SBL1, Delta
S - Flash Throughput, 56000 KB/s  (1143228 Bytes,  20404 us)
S - DDR Frequency, 400 MHz
Android Bootloader - UART_DM Initialized!!!
[0] welcome to lk

[10] platform_init()
[10] target_init()
[20] initialising mmc_slot =2
[20] Error: Command timeout error
[20] Failure getting OCR response from MMC Card
[30] MMC card failed to respond, try for SD card
[90] Done initialization of the card
[90] pm8x41_get_is_cold_boot: cold boot
[100] Not able to search the panel:
[100] Display not enabled for 24 HW type
[100] Target panel init not found!
[110] pm8x41_get_is_cold_boot: cold boot
[110] Invalid partition index
[110] Invalid partition index
[120] Invalid partition index
[120] fastboot_init()
[120] Error: ssd partition not found
[220] USB init ept @ 0x8f691000
[240] udc_start()
▒
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.0-00261
S - IMAGE_VARIANT_STRING=HAAAANAAA
S - OEM_IMAGE_VERSION_STRING=C-BPATTH
S - Boot Config, 0x000002e3
S - Core 0 Frequency, 0 MHz
B -      1544 - PBL, Start
B -      3488 - bootable_media_detect_entry, Start
B -    129004 - bootable_media_detect_success, Start
B -    129009 - elf_loader_entry, Start
B -    131560 - auth_hash_seg_entry, Start
B -    131769 - auth_hash_seg_exit, Start
B -    159400 - elf_segs_hash_verify_entry, Start
B -    218272 - PBL, End
B -    183579 - SBL1, Start
B -    234972 - pm_device_init, Start
D -     14304 - pm_device_init, Delta
B -    249764 - boot_flash_init, Start
D -         0 - boot_flash_init, Delta
B -    253790 - boot_config_data_table_init, Start
D -    429684 - boot_config_data_table_init, Delta - (0 Bytes)
B -    688049 - CDT version:3,Platform ID:24,Major ID:1,Minor ID:0,Subtype:0
B -    694241 - sbl1_ddr_set_params, Start
B -    697962 - cpr_init, Start
D -         0 - cpr_init, Delta
B -    703574 - Pre_DDR_clock_init, Start
D -       213 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta
B -    716079 - pm_driver_init, Start
D -     10156 - pm_driver_init, Delta
B -    734897 - clock_init, Start
D -        61 - clock_init, Delta
B -    745023 - Image Load, Start
D -     33276 - QSEE Image Loaded, Delta - (460664 Bytes)
B -    778329 - Image Load, Start
D -      1220 - SEC Image Loaded, Delta - (2048 Bytes)
B -    785466 - sbl1_efs_handle_cookies, Start
D -        30 - sbl1_efs_handle_cookies, Delta
B -    793366 - Image Load, Start
D -     13206 - QHEE Image Loaded, Delta - (51952 Bytes)
B -    806603 - Image Load, Start
D -     17202 - RPM Image Loaded, Delta - (149492 Bytes)
B -    823835 - Image Load, Start
D -     22753 - APPSBL Image Loaded, Delta - (479072 Bytes)
B -    846619 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -    852322 - SBL1, End
D -    671092 - SBL1, Delta
S - Flash Throughput, 56000 KB/s  (1143228 Bytes,  20404 us)
S - DDR Frequency, 400 MHz
Android Bootloader - UART_DM Initialized!!!
[0] welcome to lk

[10] platform_init()
[10] target_init()
[20] initialising mmc_slot =2
[20] Error: Command timeout error
[20] Failure getting OCR response from MMC Card
[30] MMC card failed to respond, try for SD card
[90] Done initialization of the card
[90] pm8x41_get_is_cold_boot: cold boot
[100] Not able to search the panel:
[100] Display not enabled for 24 HW type
[100] Target panel init not found!
[110] pm8x41_get_is_cold_boot: cold boot
[110] partition misc doesn't exist
[110] error in emmc_recovery_init
[120] Unable to locate /bootselect partition
[120] No 'misc' partition found
[120] Error reading MISC partition
[130] failed to get ffbm cookie[130] use_signed_kernel=0, is_unlocked=0, is_tampered=0.
[130] Loading boot image (35387392): start
[1780] Loading boot image (35387392): done
[2040] DTB Total entry: 15, DTB version: 2
[2040] Using DTB entry 0x000000f7/00000000/0x00010018/0 for device 0x000000f7/00010000/0x00010018/0
[2050] Using pmic info 0x2000b/0x0/0x0/0x0 for device 0x2000b/0x0/0x0/0x0
[2050] cmdline: root=/dev/ram0 rw rootwait console=ttyMSM0,115200n8 androidboot.emmc=true androidboot.serialno=dbe29fd androidboot.baseband=apq mdss_mdp.panel=0:dsi:0:
[2070] Updating device tree: start
[2140] Updating device tree: done
[2150] Error: Command timeout error
[2150] card sleep error: mmc_put_card_to_sleep
[2150] booting linux @ 0x80080000, ramdisk @ 0x82000000 (25272261), tags/device tree @ 0x81e00000
[2160] Jumping to kernel via monitor
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.0.0-00920-gcf20a91 (ndec@nikaia) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #25 SMP PREEMPT Wed Jun 17 09:43:51 CEST 2015
[    0.000000] CPU: AArch64 Processor [410fd030] revision 0
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] alternatives: enabling workaround for ARM errata 826319, 827319, 824069
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000086000000, size 8 MiB
[    0.000000] Reserved memory: initialized node external_image_region@86000000, compatible id removed-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000086800000, size 78 MiB
[    0.000000] Reserved memory: initialized node modem_adsp_region@86800000, compatible id removed-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x000000008b600000, size 6 MiB
[    0.000000] Reserved memory: initialized node peripheral_region@8b600000, compatible id removed-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x00000000b9000000, size 112 MiB
[    0.000000] Reserved memory: initialized node secure_region, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x000000008ec00000, size 20 MiB
[    0.000000] Reserved memory: initialized node venus_qseecom_region, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x00000000b8c00000, size 4 MiB
[    0.000000] Reserved memory: initialized node audio_region, compatible id shared-dma-pool
[    0.000000] cma: Reserved 64 MiB at 0x00000000b4c00000
[    0.000000] PERCPU: Embedded 14 pages/cpu @ffffffc034b76000 s19328 r8192 d29824 u57344
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 234864
[    0.000000] Kernel command line: root=/dev/ram0 rw rootwait console=ttyMSM0,115200n8 androidboot.emmc=true androidboot.serialno=dbe29fd androidboot.baseband=apq mdss_mdp.panel=0:dsi:0:
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] software IO TLB [mem 0xaf800000-0xb3800000] (64MB) mapped at [ffffffc02f800000-ffffffc0337fffff]
[    0.000000] Memory: 618196K/954368K available (6496K kernel code, 425K rwdata, 2560K rodata, 268K init, 2246K bss, 131372K reserved, 204800K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc2000000 - 0xffffffbdc3000000   (    16 MB actual)
[    0.000000]     fixed   : 0xffffffbffabfe000 - 0xffffffbffac00000   (     8 KB)
[    0.000000]     PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000   (    16 MB)
[    0.000000]     modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc040000000   (  1024 MB)
[    0.000000]       .init : 0xffffffc00095b000 - 0xffffffc00099e000   (   268 KB)
[    0.000000]       .text : 0xffffffc000080000 - 0xffffffc00095a324   (  9065 KB)
[    0.000000]       .data : 0xffffffc0009a3000 - 0xffffffc000a0d600   (   426 KB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[    0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
[    0.000236] Console: colour dummy device 80x25
[    0.000252] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000262] pid_max: default: 32768 minimum: 301
[    0.000324] Security Framework initialized
[    0.000372] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.000382] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.000913] Initializing cgroup subsys blkio
[    0.000928] Initializing cgroup subsys memory
[    0.000954] Initializing cgroup subsys devices
[    0.000966] Initializing cgroup subsys hugetlb
[    0.001257] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[    0.001288] EFI services will not be available.
[    0.080005] CPU1: Booted secondary processor
[    0.080017] Detected VIPT I-cache on CPU1
[    0.099979] CPU2: Booted secondary processor
[    0.099997] Detected VIPT I-cache on CPU2
[    0.119988] CPU3: Booted secondary processor
[    0.119997] Detected VIPT I-cache on CPU3
[    0.120063] Brought up 4 CPUs
[    0.120088] SMP: Total of 4 processors activated.
[    0.120110] alternatives: patching kernel code
[    0.120568] devtmpfs: initialized
[    0.121372] DMI not present or invalid.
[    0.127106] pinctrl core: initialized pinctrl subsystem
[    0.138985] NET: Registered protocol family 16
[    0.169745] cpuidle: using governor ladder
[    0.199756] cpuidle: using governor menu
[    0.199918] vdso: 2 pages (1 code @ ffffffc0009a9000, 1 data @ ffffffc0009a8000)
[    0.199961] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.200719] DMA: preallocated 256 KiB pool for atomic allocations
[    0.200804] msm_smd_init: unable to create SMD logging context
[    0.200811] msm_smd_init: unable to create SMSM logging context
[    0.200999] msm_smem_init: unable to create logging context
[    0.201199] Serial: AMBA PL011 UART driver
[    0.204586] msm_smd_probe: enable_irq_wake() failed on 130
[    0.204598] smd_channel_probe_now: allocation table not initialized
[    0.204851] msm_smsm_probe: enable_irq_wake() failed on 131
[    0.205302] msm_smd_probe: enable_irq_wake() failed on 132
[    0.205312] smd_channel_probe_now: allocation table not initialized
[    0.205566] msm_smsm_probe: enable_irq_wake() failed on 133
[    0.205835] msm_smd_probe: enable_irq_wake() failed on 134
[    0.225127] platform a21b000.qcom,pronto: assigned reserved memory node peripheral_region@8b600000
[    0.225244] platform 1de0000.qcom,venus: assigned reserved memory node venus_qseecom_region
[    0.226095] irq: no irq domain found for /soc/qcom,mdss_mdp@1a00000 !
[    0.262162] msm_iommu 1f00000.qcom,iommu: invalid resource
[    0.262264] msm_iommu 1f00000.qcom,iommu: iface: 100000000, core: 0
[    0.262285] msm_iommu 1f00000.qcom,iommu: device gfx_iommu (model: 500) mapped at ffffff80003a0000, with 2 ctx banks
[    0.262374] genirq: Setting trigger mode 1 for irq 153 failed (gic_set_type+0x0/0xdc)
[    0.262438] msm_iommu 1f00000.qcom,iommu: Request Global CFG IRQ 153 failed with ret=-22
[    0.263002] msm_iommu 1e00000.qcom,iommu: iface: 100000000, core: 0
[    0.263041] msm_iommu 1e00000.qcom,iommu: device apps_iommu (model: 500) mapped at ffffff8000680000, with 20 ctx banks
[    0.263137] genirq: Setting trigger mode 1 for irq 153 failed (gic_set_type+0x0/0xdc)
[    0.263181] msm_iommu 1e00000.qcom,iommu: Request Global CFG IRQ 153 failed with ret=-22
[    0.267450] msm_iommu_ctx 1f09000.qcom,iommu-ctx: context gfx3d_user using bank 1
[    0.267608] msm_iommu_ctx 1f0a000.qcom,iommu-ctx: context gfx3d_priv using bank 2
[    0.267755] msm_iommu_ctx 1e22000.qcom,iommu-ctx: context jpeg_enc0 using bank 2
[    0.267876] msm_iommu_ctx 1e23000.qcom,iommu-ctx: context vfe using bank 3
[    0.267994] msm_iommu_ctx 1e24000.qcom,iommu-ctx: context mdp_0 using bank 4
[    0.268115] msm_iommu_ctx 1e25000.qcom,iommu-ctx: context venus_ns using bank 5
[    0.268239] msm_iommu_ctx 1e26000.qcom,iommu-ctx: context cpp using bank 6
[    0.268358] msm_iommu_ctx 1e27000.qcom,iommu-ctx: context mDSP using bank 7
[    0.268477] msm_iommu_ctx 1e28000.qcom,iommu-ctx: context gss using bank 8
[    0.268597] msm_iommu_ctx 1e29000.qcom,iommu-ctx: context a2 using bank 9
[    0.268722] msm_iommu_ctx 1e32000.qcom,iommu-ctx: context mdp_1 using bank 18
[    0.268852] msm_iommu_ctx 1e33000.qcom,iommu-ctx: context venus_sec_pixel using bank 19
[    0.268971] msm_iommu_ctx 1e34000.qcom,iommu-ctx: context venus_sec_bitstream using bank 20
[    0.269095] msm_iommu_ctx 1e35000.qcom,iommu-ctx: context venus_sec_non_pixel using bank 21
[    0.269215] msm_iommu_ctx 1e36000.qcom,iommu-ctx: context venus_fw using bank 22
[    0.269342] msm_iommu_ctx 1e37000.qcom,iommu-ctx: context periph_rpm using bank 23
[    0.269462] msm_iommu_ctx 1e38000.qcom,iommu-ctx: context periph_CE using bank 24
[    0.269586] msm_iommu_ctx 1e39000.qcom,iommu-ctx: context periph_BLSP using bank 25
[    0.269709] msm_iommu_ctx 1e3a000.qcom,iommu-ctx: context periph_SDC1 using bank 26
[    0.269833] msm_iommu_ctx 1e3b000.qcom,iommu-ctx: context periph_SDC2 using bank 27
[    0.269968] msm_iommu_ctx 1e3c000.qcom,iommu-ctx: context periph_audio using bank 28
[    0.270092] msm_iommu_ctx 1e3d000.qcom,iommu-ctx: context periph_USB_HS1 using bank 29
[    0.270507] qcom_iommu: iommu sec: psize[0]: 94208, psize[1]: 0
[    0.270855] vgaarb: loaded
[    0.271126] SCSI subsystem initialized
[    0.271487] usbcore: registered new interface driver usbfs
[    0.271536] usbcore: registered new interface driver hub
[    0.271594] usbcore: registered new device driver usb
[    0.272360] Advanced Linux Sound Architecture Driver Initialized.
[    0.273343] cfg80211: Calling CRDA to update world regulatory domain
[    0.273373] Switched to clocksource arch_sys_counter
[    0.280524] NET: Registered protocol family 2
[    0.281031] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.281143] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[    0.281328] TCP: Hash tables configured (established 8192 bind 8192)
[    0.281388] TCP: reno registered
[    0.281400] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.281437] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.281594] NET: Registered protocol family 1
[    0.281794] RPC: Registered named UNIX socket transport module.
[    0.281802] RPC: Registered udp transport module.
[    0.281807] RPC: Registered tcp transport module.
[    0.281813] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.281993] Unpacking initramfs...
[    1.659440] Freeing initrd memory: 24676K (ffffffc002000000 - ffffffc003819000)
[    1.659932] kvm [1]: HYP mode not available
[    1.661398] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    1.661510] audit: initializing netlink subsys (disabled)
[    1.661547] audit: type=2000 audit(1.649:1): initialized
[    1.661995] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.669701] VFS: Disk quotas dquot_6.5.2
[    1.669867] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.672843] fuse init (API version 7.23)
[    1.673349] 9p: Installing v9fs 9p2000 file system support
[    1.674437] io scheduler noop registered
[    1.674710] io scheduler cfq registered (default)
[    1.676595] pil: failed to find qcom,msm-imem-pil node
[    1.676746] pil_tz_driver_probe: enter
[    1.677506] venus: Power-on latency exceeded, new value 25208 ns
[    1.677513] pil_tz_driver_probe: enter
[    1.681099] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.682560] msm_serial 78b0000.serial: msm_serial: detected port #0
[    1.682653] msm_serial 78b0000.serial: uartclk = 3686400
[    1.682702] 78b0000.serial: ttyMSM0 at MMIO 0x78b0000 (irq = 135, base_baud = 230400) is a MSM
[    1.682873] msm_serial: console setup on port #0
[    2.739966] console [ttyMSM0] enabled
[    2.745034] msm_serial: driver initialized
[    2.749055] [drm] Initialized drm 1.1.0 20060810
[    2.752516] mdss: Power-on latency exceeded, new value 22083 ns
[    2.758278] oxili: Power-on latency exceeded, new value 20104 ns
[    2.764169] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[    2.769014] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[    2.776283] msm_dsi_manager_register: failed to register mipi dsi host for DSI 0
[    2.783386] msm 1a00000.qcom,mdss_mdp: failed to bind 1a98000.qcom,mdss_dsi (ops dsi_ops): -517
[    2.791217] msm 1a00000.qcom,mdss_mdp: master bind failed: -517
[    2.799192] platform 1a00000.qcom,mdss_mdp: Driver msm requests probe deferral
[    2.810083] loop: module loaded
[    2.813610] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
[    2.817583] tun: Universal TUN/TAP device driver, 1.6
[    2.820931] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.826714] usbcore: registered new interface driver asix
[    2.832000] usbcore: registered new interface driver ax88179_178a
[    2.837491] usbcore: registered new interface driver cdc_ether
[    2.843603] usbcore: registered new interface driver dm9601
[    2.849268] usbcore: registered new interface driver net1080
[    2.854751] usbcore: registered new interface driver plusb
[    2.860644] usbcore: registered new interface driver cdc_subset
[    2.865950] usbcore: registered new interface driver zaurus
[    2.871781] usbcore: registered new interface driver cdc_ncm
[    2.877435] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.883178] ehci-pci: EHCI PCI platform driver
[    2.889568] ehci-platform: EHCI generic platform driver
[    2.894214] ehci-msm: Qualcomm On-Chip EHCI Host Controller
[    2.899261] msm_hsusb_host 78d9000.ehci: unable to find transceiver
[    2.904643] platform 78d9000.ehci: Driver msm_hsusb_host requests probe deferral
[    2.910943] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.918526] ohci-pci: OHCI PCI platform driver
[    2.924543] ohci-platform: OHCI generic platform driver
[    2.929152] usbcore: registered new interface driver cdc_acm
[    2.934051] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.940009] usbcore: registered new interface driver usblp
[    2.947719] usbcore: registered new interface driver cdc_wdm
[    2.953262] usbcore: registered new interface driver uas
[    2.959104] usbcore: registered new interface driver usb-storage
[    2.964453] usbcore: registered new interface driver usbserial
[    2.980787] usb3503 usb2513: switched to HUB mode
[    2.980808] usb3503 usb2513: usb3503_probe: probed in hub mode
[    2.984893] msm_otg 78d9000.phy: OTG regs = ffffff80003be000
[    2.990588] platform 78d9000.phy: Driver msm_otg requests probe deferral
[    2.996493] platform 78d9000.usb: Driver msm_hsusb requests probe deferral
[    3.003496] usbip_core: USB/IP Core v1.0.0
[    3.009407] usbcore: registered new device driver usbip-host
[    3.013469] usbip_host: USB/IP Host Driver v1.0.0
[    3.019531] mousedev: PS/2 mouse device common for all mice
[    3.024760] i2c_qup 78b8000.i2c:
[    3.024760]  tx channel not available
[    3.030247] qcom-tsens 4a8000.thermal-sensor: tsens calibration failed
[    3.036253] platform 4a8000.thermal-sensor: Driver qcom-tsens requests probe deferral
[    3.042921] Driver 'mmcblk' needs updating - please use bus_type methods
[    3.050767] sdhci: Secure Digital Host Controller Interface driver
[    3.057485] sdhci: Copyright(c) Pierre Ossman
[    3.063496] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.076228] 8916_l5: unsupportable voltage range: 2700000-1800000uV
[    3.076249] mmc0: Switching to 3.3V signalling voltage failed
[    3.113351] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[    3.114068] sdhci_msm 7864900.sdhci: Got CD GPIO
[    3.173449] mmc1: SDHCI controller on 7864900.sdhci [7864900.sdhci] using ADMA 64-bit
[    3.175173] ledtrig-cpu: registered to indicate activity on CPUs
[    3.180845] usbcore: registered new interface driver usbhid
[    3.181150] mmc0: MAN_BKOPS_EN bit is not set
[    3.186051] mmc0: new high speed MMC card at address 0001
[    3.186344] mmcblk0: mmc0:0001 DS2008 7.28 GiB
[    3.186434] mmcblk0boot0: mmc0:0001 DS2008 partition 1 4.00 MiB
[    3.186517] mmcblk0boot1: mmc0:0001 DS2008 partition 2 4.00 MiB
[    3.186597] mmcblk0rpmb: mmc0:0001 DS2008 partition 3 4.00 MiB
[    3.199255] Alternate GPT is invalid, using primary GPT.
[    3.199288]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10
[    3.229028] usbhid: USB HID core driver
[    3.234373] msm8916-pinctrl 1000000.pinctrl: Invalid config param 000a
[    3.237540] msm8916-pinctrl 1000000.pinctrl: pin_config_group_set op failed for group 121
[    3.244155] extcon-usb-gpio usb-id: Error applying setting, reverse things back
[    3.256054] qcom-apq8016 7702000.sound: error getting codec dai name
[    3.259502] qcom-apq8016 7702000.sound: Error resolving dai links: -517
[    3.266153] platform 7702000.sound: Driver qcom-apq8016 requests probe deferral
[    3.267003] mmc1: new high speed SDHC card at address aaaa
[    3.267258] mmcblk1: mmc1:aaaa SS08G 7.40 GiB
[    3.271109]  mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10
[    3.289950] TCP: cubic registered
[    3.294853] NET: Registered protocol family 17
[    3.298075] 9pnet: Installing 9P2000 support
[    3.302439] Key type dns_resolver registered
[    3.307472] registered taskstats version 1
[    3.312905] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[    3.315108] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[    3.337152] msm 1a00000.qcom,mdss_mdp: bound 1a98000.qcom,mdss_dsi (ops dsi_ops)
[    3.337190] msm 1a00000.qcom,mdss_mdp: bound 1c00000.qcom,adreno-3xx (ops a3xx_ops)
[    3.343672] 1a00000.qcom,mdss_mdp supply vdd not found, using dummy regulator
[    3.367694] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    3.367715] [drm] No driver support for vblank timestamp query.
[    3.574427] Console: switching to colour frame buffer device 240x67
[    3.611192] msm 1a00000.qcom,mdss_mdp: fb0: msm frame buffer device
[    3.616238] msm 1a00000.qcom,mdss_mdp: registered panic notifier
[    3.643372] [drm] Initialized msm 1.0.0 20130625 on minor 0
[    3.643676] msm_hsusb_host 78d9000.ehci: unable to find transceiver
[    3.647752] platform 78d9000.ehci: Driver msm_hsusb_host requests probe deferral
[    3.654429] msm_otg 78d9000.phy: OTG regs = ffffff8000506000
[    3.778968] qcom-apq8016 7702000.sound: adv7511 <-> Quatenary MI2S mapping ok
[    3.779720] msm_hsusb_host 78d9000.ehci: EHCI Host Controller
[    3.785229] ../drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    3.785249] msm_hsusb_host 78d9000.ehci: new USB bus registered, assigned bus number 1
[    3.785428] msm_hsusb_host 78d9000.ehci: irq 144, io mem 0x078d9000
[    3.803351] msm_hsusb_host 78d9000.ehci: USB 2.0 started, EHCI 1.00
[    3.803490] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.803497] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.803501] usb usb1: Product: EHCI Host Controller
[    3.803506] usb usb1: Manufacturer: Linux 4.0.0-00920-gcf20a91 ehci_hcd
[    3.803511] usb usb1: SerialNumber: 78d9000.ehci
[    3.803989] hub 1-0:1.0: USB hub found
[    3.804013] hub 1-0:1.0: 1 port detected
[    3.857837] ALSA devi▒▒▒R▒+▒V$$▒k▒▒֫▒▒▒RHh            ▒&      ▒▒▒▒▒▒2%▒▒▒▒▒▒▒▒▒͕▒▒Z▒ɹ▒▒▒▒▒▒▒▒▒▒▒▒▒Z▒B2▒▒▒▒▒▒▒▒ʪ▒▒j2▒▒▒▒▒▒▒▒▒▒*▒▒JjR▒           ▒&      ▒▒▒�▒2%▒▒▒▒▒▒▒▒ѕɹ▒ѥٕ́▒▒▒▒▒▒▒▒▒ZB2▒▒▒▒▒▒▒▒▒▒*▒▒j2▒▒▒▒▒▒▒▒▒
                                               ł▒▒Jj▒▒Starting logging: OK
Initializing random number generator... [    4.699335] input: Logitech USB Optical Mouse as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C077.0[    3.908862] random: dd urandom read with 6 bits of entropy available
001/input/input0
PuTTYPuTTYPuTTYPuTTYdone.
Starting network...
[    4.753454] hid-generic 0003:046D:C077.0001: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-78d9000.ehci-1.1/input0
[    3.953707] EXT3-fs (mmcblk1p10): error: couldn't mount because of unsupported optional features (40)
[    3.954834] EXT2-fs (mmcblk1p10): error: couldn't mount because of unsupported optional features (44)
[    4.833496] usb 1-1.2: new full-speed USB device number 4 using msm_hsusb_host
[    3.991132] EXT4-fs (mmcblk1p10): recovery complete
[    3.992577] EXT4-fs (mmcblk1p10): mounted filesystem with ordered data mode. Opts: (null)

Welcome to Buildroot
buildroot login: [    4.123436] usb 1-1: new high-speed USB device number 2 using msm_hsusb_host
[    4.946147] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Password:
New Image "debian"
New Image "debian"
New Image "Linaro Linux Desktop for DragonBoard 410c - Build #36"
New Image, can install "debian"
New Image "lost+found"
[    4.959142] usb 1-1.2: Manufacturer: Logitech
[    4.966909] input: Logitech USB Receiver as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.2/1-1.2:1.0/0003:046D:C52B.0002/input/input1
[    4.273825] usb 1-1: New USB device found, idVendor=0424, idProduct=2513
[    4.273857] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    4.280214] hub 1-1:1.0: USB hub found
[    4.287067] hub 1-1:1.0: 3 ports detected
[    5.023447] hid-generic 0003:046D:C52B.0002: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-78d9000.ehci-1.2/input0
[    5.027422] input: Logitech USB Receiver as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.2/1-1.2:1.1/0003:046D:C52B.0003/input/input2
[    5.093563] hid-generic 0003:046D:C52B.0003: input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-78d9000.ehci-1.2/input1
[    5.097253] hid-generic 0003:046D:C52B.0004: device has no listeners, quitting
▒
[    4.563569] usb 1-1.1: new low-speed USB device number 3 using msm_hsusb_host
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.0-00261
[    4.677688] usb 1-1.1: New USB device found, idVendor=046d, idProduct=c077
[    4.677716] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.683656] usb 1-1.1: Product: USB Optical Mouse
[    4.690679] usb 1-1.1: Manufacturer: Logitech
[    4.699396] input: Logitech USB Optical Mouse as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C077.0001/input/input0
S - IMAGE_VARIANT_STRING=HAAAANAAA
[    4.753531] hid-generic 0003:046D:C077.0001: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-78d9000.ehci-1.1/input0
S - OEM_IMAGE_VERSION_STRING=C-BPATTH
S - Boot Config, 0x000002e3
S - Core 0 Frequency, 0 MHz
[    4.833572] usb 1-1.2: new full-speed USB device number 4 using msm_hsusb_host
B -      1544 - PBL, Start
B -      3488 - bootable_media_detect_entry, Start
B -    128987 - bootable_media_detect_success, Start
[    4.946191] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c52b
[    4.946220] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.951956] usb 1-1.2: Product: USB Receiver
[    4.959210] usb 1-1.2: Manufacturer: Logitech
B -    128992 - elf_loader_entry, Start
[    4.969982] input: Logitech USB Receiver as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.2/1-1.2:1.0/0003:046D:C52B.0002/input/input1
[    5.023509] hid-generic 0003:046D:C52B.0002: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-78d9000.ehci-1.2/input0
[    5.027534] input: Logitech USB Receiver as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.2/1-1.2:1.1/0003:046D:C52B.0003/input/input2
B -    131549 - auth_hash_seg_entry, Start
B -    131758 - auth_hash_seg_exit, Start
[    5.093627] hid-generic 0003:046D:C52B.0003: input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-78d9000.ehci-1.2/input1
[    5.097326] hid-generic 0003:046D:C52B.0004: device has no listeners, quitting
B -    159387 - elf_segs_hash_verify_entry, Start
B -    218260 - PBL, End
B -    185928 - SBL1, Start
B -    237991 - pm_device_init, Start
D -     14335 - pm_device_init, Delta
B -    252814 - boot_flash_init, Start
D -        30 - boot_flash_init, Delta
B -    256810 - boot_config_data_table_init, Start
D -    429501 - boot_config_data_table_init, Delta - (0 Bytes)
B -    690916 - CDT version:3,Platform ID:24,Major ID:1,Minor ID:0,Subtype:0
B -    697108 - sbl1_ddr_set_params, Start
B -    700829 - cpr_init, Start
D -         0 - cpr_init, Delta
B -    706441 - Pre_DDR_clock_init, Start
D -       213 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta
B -    718946 - pm_driver_init, Start
D -      9211 - pm_driver_init, Delta
B -    736819 - clock_init, Start
D -        61 - clock_init, Delta
B -    746945 - Image Load, Start
D -     33306 - QSEE Image Loaded, Delta - (460664 Bytes)
B -    780281 - Image Load, Start
D -      1189 - SEC Image Loaded, Delta - (2048 Bytes)
B -    787418 - sbl1_efs_handle_cookies, Start
D -         0 - sbl1_efs_handle_cookies, Delta
B -    795318 - Image Load, Start
D -     13206 - QHEE Image Loaded, Delta - (51952 Bytes)
B -    808555 - Image Load, Start
D -     17171 - RPM Image Loaded, Delta - (149492 Bytes)
B -    825757 - Image Load, Start
D -     22784 - APPSBL Image Loaded, Delta - (479072 Bytes)
B -    848540 - QSEE Execution, Start
D -        91 - QSEE Execution, Delta
B -    854244 - SBL1, End
D -    670664 - SBL1, Delta
S - Flash Throughput, 56000 KB/s  (1143228 Bytes,  20404 us)
S - DDR Frequency, 400 MHz
Android Bootloader - UART_DM Initialized!!!
[0] welcome to lk

[10] platform_init()
[10] target_init()
[20] initialising mmc_slot =2
[20] Error: Command timeout error
[20] Failure getting OCR response from MMC Card
[30] MMC card failed to respond, try for SD card
[90] Done initialization of the card
[90] pm8x41_get_is_cold_boot: cold boot
[100] Not able to search the panel:
[100] Display not enabled for 24 HW type
[100] Target panel init not found!
[110] pm8x41_get_is_cold_boot: cold boot
Login incorrect
buildroot login: [110] partition misc doesn't exist
Password:
[120] Unable to locate /bootselect partition
[120] No 'misc' partition found
[120] Error reading MISC partition
[130] failed to get ffbm cookie[130] use_signed_kernel=0, is_unlocked=0, is_tampered=0.
[130] Loading boot image (35387392): start
[1780] Loading boot image (35387392): done
[2040] DTB Total entry: 15, DTB version: 2
[2040] Using DTB entry 0x000000f7/00000000/0x00010018/0 for device 0x000000f7/00010000/0x00010018/0
[2050] Using pmic info 0x2000b/0x0/0x0/0x0 for device 0x2000b/0x0/0x0/0x0
[2050] cmdline: root=/dev/ram0 rw rootwait console=ttyMSM0,115200n8 androidboot.emmc=true androidboot.serialno=dbe29fd androidboot.baseband=apq mdss_mdp.panel=0:dsi:0:
[2070] Updating device tree: start
[2140] Updating device tree: done
[2150] Error: Command timeout error
[2150] card sleep error: mmc_put_card_to_sleep
[2150] booting linux @ 0x80080000, ramdisk @ 0x82000000 (25272261), tags/device tree @ 0x81e00000
[2160] Jumping to kernel via monitor

Login incorrect
buildroot login: ▒


#2

hi,

sorry, i missed this post…

So there is one big different between 1) booting the SD installer, and 2) booting the latest Debian release from eMMC… and it is the kernel. The SD installer is running the same kernel we had at the launch, back in June… I have never updated the kernel (If it ain’t broke, don’t fix it).

Over the last few weeks, I was working on a new version of the SD installer, and among many other things, it would be using our current kernel… My goal is to have it ready sometimes before the end of Feb). As soon as I have an initial image that you can test, I can let you know. If this is urgent, I can try to cook up a quick hack…


#3

Hi @ndec
The workaround is trivial, just unplug the Linker card when you are reflashing the 410c board. I can easily wait until you have the next gen SD installer ready. Thanks.