2nd board - Out of the Box - Will not complete boot

First board would not boot. I eventually was able to get serial cable set up and posted info on previous post. Hung Boot Android and Recovery Image - UART Output - #2 by danielt

I ordered a second board. Pulled it straight out of the box, hooked up monitor, keyboard, mouse and UART pins for serial to USB. Checked S6 0-0-0-0, plugged it in and it began to boot. It gets to about 20 seconds in the boot and restarts. Let it roll in the reboot for 30 min. No Change. Powered down and unplugged Keyboard and mouse. Power back up. Continues in the loop, restarting at the same point.

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.06.13 18:58:46 =~=~=~=~=~=~=~=~=~=~=~=

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.0-00261
S - IMAGE_VARIANT_STRING=HAAAANAAA
S - OEM_IMAGE_VERSION_STRING=C-BPATTH
S - Boot Config, 0x000002e1
S - Core 0 Frequency, 0 MHz
B - 1547 - PBL, Start
B - 3493 - bootable_media_detect_entry, Start
B - 157435 - bootable_media_detect_success, Start
B - 157439 - elf_loader_entry, Start
B - 159664 - auth_hash_seg_entry, Start
B - 159875 - auth_hash_seg_exit, Start
B - 175509 - elf_segs_hash_verify_entry, Start
B - 235101 - PBL, End
B - 241377 - SBL1, Start
B - 304237 - pm_device_init, Start
D - 14701 - pm_device_init, Delta
B - 319548 - boot_flash_init, Start
D - 30 - boot_flash_init, Delta
B - 323574 - boot_config_data_table_init, Start
D - 30439 - boot_config_data_table_init, Delta - (0 Bytes)
B - 358558 - CDT version:3,Platform ID:24,Major ID:1,Minor ID:0,Subtype:0
B - 364780 - sbl1_ddr_set_params, Start
B - 368470 - cpr_init, Start
D - 0 - cpr_init, Delta
B - 374082 - Pre_DDR_clock_init, Start
D - 183 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 386587 - pm_driver_init, Start
D - 6832 - pm_driver_init, Delta
B - 402081 - clock_init, Start
D - 30 - clock_init, Delta
B - 412238 - Image Load, Start
D - 31994 - QSEE Image Loaded, Delta - (460664 Bytes)
B - 444263 - Image Load, Start
D - 610 - SEC Image Loaded, Delta - (2048 Bytes)
B - 451430 - sbl1_efs_handle_cookies, Start
D - 3690 - sbl1_efs_handle_cookies, Delta
B - 459116 - Image Load, Start
D - 12505 - QHEE Image Loaded, Delta - (51952 Bytes)
B - 471652 - Image Load, Start
D - 19032 - RPM Image Loaded, Delta - (149492 Bytes)
B - 490714 - Image Load, Start
D - 14488 - APPSBL Image Loaded, Delta - (512352 Bytes)
B - 505232 - QSEE Execution, Start
D - 91 - QSEE Execution, Delta
B - 510936 - SBL1, End
D - 271907 - SBL1, Delta
S - Flash Throughput, 108000 KB/s (1176508 Bytes, 10858 us)
S - DDR Frequency, 400 MHz
Android Bootloader - UART_DM Initialized!!!
[0] [0] welcome to lk

[10] [10] platform_init()
[10] [10] target_init()
[50] [50] SDHC Running in HS200 mode
[70] [70] Done initialization of the card
[80] [80] pm8x41_get_is_cold_boot: cold boot
[80] [80] No ‘frp’ partition found
[90] [90] Not able to search the panel:
[90] [90] Display not enabled for 24 HW type
[90] [90] Target panel init not found!
[100] [100] pm8x41_get_is_cold_boot: cold boot
[100] [100] Unable to locate /bootselect partition
[110] [110] boot_verifier: Device is in ORANGE boot state.
[110] [110] Device is unlocked! Skipping verification…
[120] [120] Loading boot image (16521216): start
[240] [240] Loading boot image (16521216): done
[240] [240] use_signed_kernel=1, is_unlocked=1, is_tampered=0.
[710] [710] DTB Total entry: 212, DTB version: 3
[710] [710] Using DTB entry 0x000000f7/00000000/0x00000018/0 for device 0x000000f7/00010000/0x00010018/0
[720] [720] target_display_panel_node:510: hw_id=24 panel_name=""
[720] [720] cmdline: console=ttyHSL0,115200,n8 androidboot.console=ttyHSL0 androidboot.hardware=qcom msm_rtb.filter=0x237 ehci-hcd.park=3 androidboot.bootdevice=7824900.sdhci lpm_levels.sleep_disabled=1 earlyprintk androidboot.selinux=permissive androidboot.emmc=true[750] [750] Updating device tree: start
[760] [760] Updating device tree: done
[770] [770] booting linux @ 0x80080000, ramdisk @ 0x82000000 (795398), tags/device tree @ 0x81e00000
[780] [780] Jumping to kernel via monitor
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.49-g0b014e2-00001-gebe2063 (buildslave@aosp-x86-64-08) (gcc version 4.9.x-google 20140827 (prerelease) (GCC) ) #9 SMP PREEMPT Wed Dec 2 10:33:57 UTC 2015
[ 0.000000] CPU: AArch64 Processor [410fd030] revision 0
[ 0.000000] Machine: Qualcomm Technologies, Inc. APQ 8016 SBC
[ 0.000000] No earlyprintk arguments passed.
[ 0.000000] cma: Found external_image__region@0, memory base 0x0000000086000000, size 8 MiB, limit 0xffffffffffffffff
[ 0.000000] cma: Found modem_adsp_region@0, memory base 0x0000000086800000, size 43 MiB, limit 0xffffffffffffffff
[ 0.000000] cma: Found pheripheral_region@0, memory base 0x0000000089300000, size 6 MiB, limit 0xffffffffffffffff
[ 0.000000] cma: Found secure_region@0, memory base 0x0000000000000000, size 109 MiB, limit 0xffffffffffffffff
[ 0.000000] cma: Found venus_qseecom_region@0, memory base 0x0000000000000000, size 18 MiB, limit 0x0000000090000000
[ 0.000000] cma: Found audio_region@0, memory base 0x0000000000000000, size 3 MiB, limit 0xffffffffffffffff
[ 0.000000] cma: Found splash_region@83000000, memory base 0x0000000083000000, size 20 MiB, limit 0xffffffffffffffff
[ 0.000000] cma: CMA: reserved 8 MiB at 0x0000000086000000 for external_image_mem
[ 0.000000] cma: CMA: reserved 43 MiB at 0x0000000086800000 for modem_adsp_mem
[ 0.000000] cma: CMA: reserved 6 MiB at 0x0000000089300000 for peripheral_mem
[ 0.000000] cma: CMA: reserved 112 MiB at 0x00000000b9000000 for secure_mem
[ 0.000000] cma: CMA: reserved 20 MiB at 0x000000008ec00000 for venus_qseecom_mem
[ 0.000000] cma: CMA: reserved 4 MiB at 0x00000000b8c00000 for audio_mem
[ 0.000000] cma: CMA: reserved 20 MiB at 0x0000000083000000 for cont_splash_mem
[ 0.000000] cma: CMA: reserved 64 MiB at 0x00000000b4c00000 for default region
[ 0.000000] PERCPU: Embedded 17 pages/cpu @ffffffc034ac7000 s40000 r8192 d21440 u69632
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 243456
[ 0.000000] Kernel command line: sched_enable_hmp=1 console=ttyHSL0,115200,n8 androidboot.console=ttyHSL0 androidboot.hardware=qcom msm_rtb.filter=0x237 ehci-hcd.park=3 androidboot.bootdevice=7824900.sdhci lpm_levels.sleep_disabled=1 earlyprintk androidboot.selinux=permissive androidboot.emmc=true androidboot.serialno=35d62e10 androidboot.baseband=apq mdss_mdp.panel=0:dsi:0:
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] software IO TLB [mem 0xb3800000-0xb3900000] (1MB) mapped at [ffffffc033800000-ffffffc0338fffff]
[ 0.000000] Memory: 717372K/990208K available (12320K kernel code, 1756K rwdata, 5532K rodata, 2787K init, 1811K bss, 272836K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB)
[ 0.000000] vmemmap : 0xffffffbc02000000 - 0xffffffbc03000000 ( 16 MB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc040000000 ( 1024 MB)
[ 0.000000] .init : 0xffffffc001400000 - 0xffffffc0016b8c40 ( 2788 kB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc00136f3d4 ( 19389 kB)
[ 0.000000] .data : 0xffffffc0016b9000 - 0xffffffc001870128 ( 1757 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] HMP scheduling enabled.
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
[ 0.004548] Calibrating delay loop (skipped), value calculated using timer frequency… 38.40 BogoMIPS (lpj=192000)
[ 0.004567] pid_max: default: 32768 minimum: 301
[ 0.004946] Security Framework initialized
[ 0.004978] SELinux: Initializing.
[ 0.005175] Mount-cache hash table entries: 256
[ 0.006916] Initializing cgroup subsys debug
[ 0.006934] Initializing cgroup subsys freezer
[ 0.007489] /cpus/cpu@0: Unknown CPU type
[ 0.007504] /cpus/cpu@1: Unknown CPU type
[ 0.007518] /cpus/cpu@2: Unknown CPU type
[ 0.007533] /cpus/cpu@3: Unknown CPU type
[ 0.008547] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.010153] ftrace: Allocated trace_printk buffers
[ 0.019642] Core Debug Lock unlocked
[ 0.020306] MSM Memory Dump base table set up
[ 0.020340] MSM Memory Dump apps data table set up
[ 0.023658] CPU1: Booted secondary processor
[ 0.032896] CPU2: Booted secondary processor
[ 0.035472] CPU3: Booted secondary processor
[ 0.035675] Brought up 4 CPUs
[ 0.035696] SMP: Total of 4 processors activated.
[ 0.069926] pinctrl core: initialized pinctrl subsystem
[ 0.071056] regulator-dummy: no parameters
[ 0.078134] NET: Registered protocol family 16
[ 0.080287] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.137510] msm_watchdog b017000.qcom,wdt: wdog absent resource not present
[ 0.137785] msm_watchdog b017000.qcom,wdt: MSM Watchdog Initialized
[ 0.144636] spmi_pmic_arb 200f000.qcom,spmi: PMIC Arb Version-2 0x20010000
[ 0.152348] cma: Assigned CMA region at 0 to 1de0000.qcom,venus device
[ 0.153034] cma: Assigned CMA region at 0 to 4080000.qcom,mss device
[ 0.153588] cma: Assigned CMA region at 0 to a21b000.qcom,pronto device
[ 0.154623] ACC: mem_acc_efuse_init: efuse_addr = 0x0000000000058000 (len=0x1000)
[ 0.154702] ACC: mem_acc_fuse_is_setting_expected: [row:0] = 0x422008000000706 @52:1 == 1 ?: no
[ 0.154900] mem_acc_corner: 0 <–> 0 mV
[ 0.158723] vdso: 2 pages (1 code, 1 data) at base ffffffc0016c1000
[ 0.159259] msm_mpm_dev_probe(): Cannot get clk resource for XO
[ 0.159292] platform 601d0.qcom,mpm: Driver mpm-v2 requests probe deferral
[ 0.159656] smd_open() before smd_init()
[ 0.159684] platform qcom,rpm-smd.35: Driver rpm-smd requests probe deferral
[ 0.160187] msm-jtag-fuse 5e01c.jtagfuse: JTag Fuse initialized
[ 0.162992] smd_channel_probe_worker: allocation table not initialized
[ 0.164226] smd_channel_probe_worker: allocation table not initialized
[ 0.168535] 8916_s2: 1050 <–> 1350 mV at 1150 mV
[ 0.168869] spm_regulator_probe: name=8916_s2, range=LV, voltage=1150000 uV, mode=PWM, step rate=1200 uV/us
[ 0.169552] cpr_efuse_init: apc_corner: efuse_addr = 0x0000000000058000 (len=0x1000)
[ 0.169601] cpr_parse_speed_bin_fuse: apc_corner: [row: 1]: 0x1210b95acfe, speed_bits = 0
[ 0.169619] cpr_parse_pvs_version_fuse: apc_corner: [row: 0]: 0x422008000000706, pvs_version = 0
[ 0.169724] cpr_pvs_init: apc_corner: pvs voltage: [1050000 1150000 1300000] uV
[ 0.169736] cpr_pvs_init: apc_corner: ceiling voltage: [1050000 1150000 1350000] uV
[ 0.169747] cpr_pvs_init: apc_corner: floor voltage: [1050000 1050000 1162500] uV
[ 0.170162] platform b018000.regulator: Driver qcom,cpr-regulator requests probe deferral
[ 0.170771] i2c-msm-v2 78b6000.i2c: probing driver i2c-msm-v2
[ 0.170887] i2c-msm-v2 78b6000.i2c: error on clk_get(core_clk):-517
[ 0.170904] i2c-msm-v2 78b6000.i2c: error probe() failed with err:-517
[ 0.170944] platform 78b6000.i2c: Driver i2c-msm-v2 requests probe deferral
[ 0.171207] i2c-msm-v2 78b9000.i2c: probing driver i2c-msm-v2
[ 0.171310] i2c-msm-v2 78b9000.i2c: error on clk_get(core_clk):-517
[ 0.171326] i2c-msm-v2 78b9000.i2c: error probe() failed with err:-517
[ 0.171363] platform 78b9000.i2c: Driver i2c-msm-v2 requests probe deferral
[ 0.171630] i2c-msm-v2 78ba000.i2c: probing driver i2c-msm-v2
[ 0.171733] i2c-msm-v2 78ba000.i2c: error on clk_get(core_clk):-517
[ 0.171748] i2c-msm-v2 78ba000.i2c: error probe() failed with err:-517
[ 0.171785] platform 78ba000.i2c: Driver i2c-msm-v2 requests probe deferral
[ 0.172091] i2c-msm-v2 78b8000.i2c: probing driver i2c-msm-v2
[ 0.172191] i2c-msm-v2 78b8000.i2c: error on clk_get(core_clk):-517
[ 0.172206] i2c-msm-v2 78b8000.i2c: error probe() failed with err:-517
[ 0.172243] platform 78b8000.i2c: Driver i2c-msm-v2 requests probe deferral
[ 0.174456] msm-thermal qcom,msm-thermal.58: msm_thermal:Failed reading node=/soc/qcom,msm-thermal, key=qcom,rpm-phase-resource-type err=-22. KTM continues
[ 0.174476] msm-thermal qcom,msm-thermal.58: msm_thermal:Failed reading node=/soc/qcom,msm-thermal, key=qcom,gfx-sensor-id. err=-22. KTM continues
[ 0.174492] msm-thermal qcom,msm-thermal.58: probe_therm_reset:Failed reading node=/soc/qcom,msm-thermal, key=qcom,therm-reset-temp err=-22. KTM continues
[ 0.174510] msm-thermal qcom,msm-thermal.58: probe_vdd_mx:Failed reading node=/soc/qcom,msm-thermal, key=qcom,mx-restriction-temp. KTM continues
[ 0.174527] msm-thermal qcom,msm-thermal.58: probe_psm:Failed reading node=/soc/qcom,msm-thermal, key=qcom,pmic-sw-mode-temp. err=-22. KTM continues
[ 0.174600] msm_thermal:vdd_restriction_reg_init Defer regulator vdd-dig probe
[ 0.174609] msm_thermal:probe_vdd_rstr Err regulator init. err:-517. KTM continues.
[ 0.174621] msm-thermal qcom,msm-thermal.58: probe_vdd_rstr:Failed reading node=/soc/qcom,msm-thermal, key=qcom,freq-req. err=-517. KTM continues
[ 0.174634] msm_thermal:msm_thermal_dev_probe Failed reading node=/soc/qcom,msm-thermal, key=qcom,freq-control-mask. err:-517
[ 0.174663] platform qcom,msm-thermal.58: Driver msm-thermal requests probe deferral
[ 0.175457] sps:sps is ready.
[ 0.176221] platform 1800000.qcom,rpmcc: Driver qcom,rpmcc-8916 requests probe deferral
[ 0.176722] platform 1800000.qcom,gcc: Driver qcom,gcc-8916 requests probe deferral
[ 0.178475] platform b011050.qcom,clock-a7: Driver clock-a7 requests probe deferral
[ 0.180272] msm_mpm_dev_probe(): Cannot get clk resource for XO
[ 0.180303] platform 601d0.qcom,mpm: Driver mpm-v2 requests probe deferral
[ 0.181805] 8916_s1_corner: 0 <–> 0 mV at 0 mV normal idle
[ 0.182693] 8916_s1_corner_ao: 0 <–> 0 mV at 0 mV normal idle
[ 0.183497] 8916_s1_floor_corner: 0 <–> 0 mV at 0 mV normal idle
[ 0.184550] 8916_s3: 1200 <–> 1300 mV at 1300 mV normal idle
[ 0.185574] 8916_s4: 1800 <–> 2100 mV at 1800 mV normal idle
[ 0.186563] 8916_l1: 1225 mV normal idle
[ 0.187591] 8916_l2: 1200 mV normal idle
[ 0.188610] 8916_l3: 500 <–> 1287 mV at 0 mV normal idle
[ 0.189350] 8916_l3_corner_ao: 0 <–> 0 mV at 0 mV normal idle
[ 0.190123] 8916_l3_corner_so: 0 <–> 0 mV at 0 mV normal idle
[ 0.191354] 8916_l5: 1800 mV normal idle
[ 0.192362] 8916_l6: 1800 mV normal idle
[ 0.193358] 8916_l7: 1800 mV normal idle
[ 0.194174] 8916_l7_ao: 1800 mV normal idle
[ 0.194946] 8916_l7_so: 1800 mV normal idle
[ 0.195943] 8916_l8: 2850 <–> 2900 mV at 2850 mV normal idle
[ 0.196949] 8916_l9: 3300 mV normal idle
[ 0.198188] 8916_l11: 1800 <–> 2950 mV at 1800 mV normal idle
[ 0.199205] 8916_l12: 1800 <–> 2950 mV at 1800 mV normal idle
[ 0.200221] 8916_l13: 3075 mV normal idle
[ 0.202526] 8916_l15: 1800 <–> 3300 mV at 1800 mV normal idle
[ 0.204083] 8916_l16: 1800 <–> 3300 mV at 1800 mV normal idle
[ 0.205114] 8916_l17: 3300 mV normal idle
[ 0.206095] cpr_efuse_init: apc_corner: efuse_addr = 0x0000000000058000 (len=0x1000)
[ 0.206149] cpr_parse_speed_bin_fuse: apc_corner: [row: 1]: 0x1210b95acfe, speed_bits = 0
[ 0.206167] cpr_parse_pvs_version_fuse: apc_corner: [row: 0]: 0x422008000000706, pvs_version = 0
[ 0.206273] cpr_pvs_init: apc_corner: pvs voltage: [1050000 1150000 1300000] uV
[ 0.206285] cpr_pvs_init: apc_corner: ceiling voltage: [1050000 1150000 1350000] uV
[ 0.206295] cpr_pvs_init: apc_corner: floor voltage: [1050000 1050000 1162500] uV
[ 0.206705] cpr_init_cpr_efuse: apc_corner: [row:27] = 0x908dca0372851c26
[ 0.206726] cpr_init_cpr_efuse: apc_corner: CPR disable fuse = 0
[ 0.206741] cpr_init_cpr_efuse: apc_corner: Corner[1]: ro_sel = 2, target quot = 882
[ 0.206753] cpr_init_cpr_efuse: apc_corner: Corner[2]: ro_sel = 2, target quot = 882
[ 0.206766] cpr_init_cpr_efuse: apc_corner: Corner[3]: ro_sel = 2, target quot = 1136
[ 0.206853] cpr_get_corner_quot_adjustment: apc_corner: fuse corner 2 quotient adjustment scaling factor: 0.000
[ 0.206862] cpr_get_corner_quot_adjustment: apc_corner: fuse corner 3 quotient adjustment scaling factor: 0.621
[ 0.206877] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[1] = 882
[ 0.206885] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[2] = 882
[ 0.206893] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[3] = 882
[ 0.206902] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[4] = 882
[ 0.206910] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[5] = 1005
[ 0.206918] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[6] = 1065
[ 0.206926] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[7] = 1101
[ 0.206935] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[8] = 1136
[ 0.206943] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[9] = 1136
[ 0.207193] cpr_init_cpr_parameters: apc_corner: up threshold = 0, down threshold = 2
[ 0.207221] cpr_init_cpr_parameters: apc_corner: CPR is enabled by default.
[ 0.207251] cpr_config: apc_corner: Timer count: 0x17700 (for 5000 us)
[ 0.207655] apc_corner: 0 <–> 0 mV
[ 0.208347] i2c-msm-v2 78b6000.i2c: probing driver i2c-msm-v2
[ 0.208471] i2c-msm-v2 78b6000.i2c: error on clk_get(core_clk):-517
[ 0.208487] i2c-msm-v2 78b6000.i2c: error probe() failed with err:-517

–REMOVED DATA FROM LOG OUTPUT—

[ 14.089783] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 14.095374] l2tp_netlink: L2TP netlink interface
[ 14.099981] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 14.105895] l2tp_debugfs: L2TP debugfs support
[ 14.110269] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 14.125875] BMS: qpnp_vm_bms_probe: VMBMS disabled (disable-bms = 1)
[ 14.280994] CHG: qpnp_lbc_main_probe: Probe chg_dis=1 bpd=1 usb=0 batt_pres=1 batt_volt=3697761 soc=50
[ 14.289402] spmi msm8x16_wcd_codec-ffffffc0329b9000: Driver wcd-spmi-core requests probe deferral
[ 14.298205] spmi msm8x16_wcd_codec-ffffffc0329b9400: Driver wcd-spmi-core requests probe deferral
[ 14.310124] msm8x16-asoc-wcd sound.66: default codec configured
[ 14.316148] msm8x16-asoc-wcd sound.66: ASoC: CODEC (null) not registered
[ 14.321830] msm8x16-asoc-wcd sound.66: snd_soc_register_card failed (-517)
[ 14.329036] platform sound.66: Driver msm8x16-asoc-wcd requests probe deferral
[ 14.335976] spmi msm8x16_wcd_codec-ffffffc0329b9000: Driver wcd-spmi-core requests probe deferral
[ 14.344787] spmi msm8x16_wcd_codec-ffffffc0329b9400: Driver wcd-spmi-core requests probe deferral
[ 14.354023] Registering SWP/SWPB emulation handler
[ 14.358906] Loading module verification certificates
[ 14.365963] MODSIGN: Loaded cert ‘Magrathea: Glacier signing key: 91a824017f84adcf724fad84f143bce849fba347’
[ 14.375088] kmemleak: Kernel memory leak detector initialized
[ 14.375094] kmemleak: Automatic memory scanning thread started
[ 14.488257] mem_acc_corner: disabling
[ 14.490879] regulator-dummy: disabling
[ 14.496905] msm8x16-asoc-wcd sound.66: default codec configured
[ 14.502899] msm8x16-asoc-wcd sound.66: ASoC: CODEC (null) not registered
[ 14.508618] msm8x16-asoc-wcd sound.66: snd_soc_register_card failed (-517)
[ 14.515700] platform sound.66: Driver msm8x16-asoc-wcd requests probe deferral
[ 14.522719] spmi msm8x16_wcd_codec-ffffffc0329b9000: Driver wcd-spmi-core requests probe deferral
[ 14.531572] spmi msm8x16_wcd_codec-ffffffc0329b9400: Driver wcd-spmi-core requests probe deferral
[ 14.541842] file system registered
[ 14.544298] mbim_init: initialize 1 instances
[ 14.548681] mbim_init: Initialized 1 ports
[ 14.552619] mbim_bam_setup: no_ports:1
[ 14.556707] mbim_bam_setup: Initialized 1 ports
[ 14.562574] rndis_qc_init: initialize rndis QC instance
[ 14.567398] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 14.573611] android_usb gadget: Number of LUNs=2
[ 14.578237] lun0: LUN: removable file: (no medium)
[ 14.583072] lun1: LUN: removable file: (no medium)
[ 14.588504] android_usb gadget: android_usb ready
[ 14.592625] msm_hsusb msm_hsusb: [ci13xxx_start] hw_ep_max = 16
[ 14.600183] msm8x16-asoc-wcd sound.66: default codec configured
[ 14.600919] input: gpio-keys as /devices/soc.0/gpio_keys.68/input/input3
[ 14.611755] qcom,qpnp-rtc qpnp-rtc-ffffffc032972000: setting system clock to 1970-01-01 00:41:34 UTC (2494)
[ 14.612902] msm8x16-asoc-wcd sound.66: ASoC: CODEC (null) not registered
[ 14.612931] msm8x16-asoc-wcd sound.66: snd_soc_register_card failed (-517)
[ 14.613203] platform sound.66: Driver msm8x16-asoc-wcd requests probe deferral
[ 14.613306] spmi msm8x16_wcd_codec-ffffffc0329b9000: Driver wcd-spmi-core requests probe deferral
[ 14.613370] spmi msm8x16_wcd_codec-ffffffc0329b9400: Driver wcd-spmi-core requests probe deferral
[ 14.614572] msm8x16-asoc-wcd sound.66: default codec configured
[ 14.615682] msm8x16-asoc-wcd sound.66: ASoC: CODEC (null) not registered
[ 14.615708] msm8x16-asoc-wcd sound.66: snd_soc_register_card failed (-517)
[ 14.615970] platform sound.66: Driver msm8x16-asoc-wcd requests probe deferral
[ 14.687782] msm_thermal:interrupt_mode_init Interrupt mode init
[ 14.693478] /soc/qcom,lpm-levels/qcom,pm-cluster@0: No CPU phandle, assuming single cluster
[ 14.703185] spmi msm8x16_wcd_codec-ffffffc0329b9000: Driver wcd-spmi-core requests probe deferral
[ 14.708051] qcom,cc-debug-8916 1874000.qcom,cc-debug: Registered Debug Mux successfully
[ 14.709029] clock_late_init: Removing enables held for handed-off clocks
[ 14.712863] ALSA device list:
[ 14.712865] No soundcarä[ 14.732170] spmi msm8x16_wcd_codec-ffffffc0329b9400: Driver wcd-spmi-core requests probe deferral
[ 14.740444] Freeing unused kernel memory: 736K (ffffffc001600000 - ffffffc0016b8000)
[ 14.741517] msm8x16-asoc-wcd sound.66: default codec configured
[ 14.742682] msm8x16-asoc-wcd sound.66: ASoC: CODEC (null) not registered
[ 14.742711] msm8x16-asoc-wcd sound.66: snd_soc_register_card failed (-517)
[ 14.742993] platform sound.66: Driver msm8x16-asoc-wcd requests probe deferral
[ 14.743107] spmi msm8x16_wcd_codec-ffffffc0329b9000: Driver wcd-spmi-core requests probe deferral
[ 14.803044] SELinux: 2048 avtab hash slots, 8186 rules.
[ 14.825648] SELinux: 2048 avtab hash slots, 8186 rules.
[ 14.829972] SELinux: 1 users, 2 roles, 650 types, 0 bools, 1 sens, 1024 cats
[ 14.836958] SELinux: 86 classes, 8186 rules
[ 14.845370] SELinux: Completing initialization.
[ 14.848958] SELinux: Setting up existing superblocks.
[ 14.854100] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[ 14.861266] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
[ 14.868637] SELinux: initialized (dev bdev, type bdev), not configured for labeling
[ 14.876165] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[ 14.883096] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 14.890337] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
[ 14.907345] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
[ 14.913200] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
[ 14.920131] SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling
[ 14.929113] SELinux: initialized (dev devpts, type devpts), uses transition SIDs
[ 14.936510] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
[ 14.944341] SELinux: initialized (dev configfs, type configfs), not configured for labeling
[ 14.952626] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 14.959849] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[ 15.062969] type=1403 audit(2494.949:2): policy loaded auid=4294967295 ses=4294967295
[ 16.457064] init: /init.rc: 337: invalid command ‘su’
[ 16.462330] init: /init.qcom.rc: 512: user option requires a user id
[ 16.470680] init: could not import file ‘init.carrier.rc’ from ‘init.target.rc’
[ 16.481553] init: invalid uid ‘fm_radio’
[ 18.922929] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[ 18.929878] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 18.939379] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 18.946029] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 18.955173] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[ 18.974570] SELinux: initialized (dev functionfs, type functionfs), uses genfs_contexts
[ 18.982752] mmc0: Starting deferred resume
[ 19.079383] mmc0: Deferred resume completed
[ 19.089237] EXT4-fs (mmcblk0p22): mounted filesystem with ordered data mode. Opts: barrier=1,discard
[ 19.097705] SELinux: initialized (dev mmcblk0p22, type ext4), uses xattr
[ 19.104164] fs_mgr: __mount(source=/dev/block/bootdevice/by-name/system,target=/system,type=ext4)=0
[ 19.117052] EXT4-fs (mmcblk0p29): Ignoring removed nomblk_io_submit option
[ 19.129526] EXT4-fs (mmcblk0p29): recovery complete
[ 19.133369] EXT4-fs (mmcblk0p29): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 19.144030] SELinux: initialized (dev mmcblk0p29, type ext4), uses xattr
[ 19.150750] fs_mgr: check_fs(): mount(/dev/block/bootdevice/by-name/userdata,/data,ext4)=0
[ 19.166504] fs_mgr: Running /system/bin/e2fsck on /dev/block/bootdevice/by-name/userdata
[ 19.252450] e2fsck (213) used greatest stack depth: 12040 bytes left
[ 19.257916] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 19.262325] e2fsck: /dev/block/bootdevice/by-name/userdata: clean, 1500/327680 files, 137655/1310720 blocks
[ 19.283193] EXT4-fs (mmcblk0p29): mounted filesystem with ordered data mode. Opts: barrier=1,noauto_da_alloc,discard
[ 19.292770] SELinux: initialized (dev mmcblk0p29, type ext4), uses xattr
[ 19.299472] fs_mgr: __mount(source=/dev/block/bootdevice/by-name/userdata,target=/data,type=ext4)=0
[ 19.318506] EXT4-fs (mmcblk0p23): recovery complete
[ 19.322349] EXT4-fs (mmcblk0p23): mounted filesystem with ordered data mode. Opts: barrier=1
[ 19.330842] SELinux: initialized (dev mmcblk0p23, type ext4), uses xattr
[ 19.348913] EXT4-fs (mmcblk0p24): recovery complete
[ 19.352755] EXT4-fs (mmcblk0p24): mounted filesystem with ordered data mode. Opts: barrier=1
[ 19.361250] SELinux: initialized (dev mmcblk0p24, type ext4), uses xattr
[ 19.395774] SELinux: initialized (dev mmcblk0p1, type vfat), uses mountpoint labeling
[ 19.414416] pil-q6v5-mss 4080000.qcom,mss: modem: loading from 0x0000000086800000 to 0x0000000089300000
[ 19.435064] pil-q6v5-mss 4080000.qcom,mss: MBA: loading from 0x00000000b5000000 to 0x00000000b5100000
[ 19.481446] pil-q6v5-mss 4080000.qcom,mss: MBA boot done
[ 19.675975] pil-q6v5-mss 4080000.qcom,mss: modem: Brought out of reset
[ 19.738143] pil-q6v5-mss 4080000.qcom,mss: modem: Power/Clock ready interrupt received
[ 19.745059] pil-q6v5-mss 4080000.qcom,mss: Subsystem error monitoring/handling services are up
[ 19.753640] memshare: Modem Restart has happened
[ 19.754415] M-Notify: General: 7
[ 19.763687] msm8x16-asoc-wcd sound.66: default codec configured
[ 19.770068] msm8x16-asoc-wcd sound.66: ASoC: CODEC (null) not registered
[ 19.775836] msm8x16-asoc-wcd sound.66: snd_soc_register_card failed (-517)
[ 19.782898] platform sound.66: Driver msm8x16-asoc-wcd requests probe deferral
[ 19.793135] msm8x16-asoc-wcd sound.66: default codec configured
[ 19.800709] wcd-spmi-core msm8x16_wcd_codec-ffffffc0329b9000: Error: regulator not found
[ 19.820995] msm-pcm-routing qcom,msm-pcm-routing.37: ASoC: no dapm match for VOICE2_STUB_DL → Voice2 Stub → INTERNAL_BT_SCO_RX_Voice Mixer
[ 19.832790] msm-pcm-routing qcom,msm-pcm-routing.37: ASoC: Failed to add route VOICE2_STUB_DL → Voice2 Stub → INTERNAL_BT_SCO_RX_Voice Mixer
[ 19.873497] msm-pcm-routing qcom,msm-pcm-routing.37: ASoC: mux SLIM_0_RX AANC MUX has no paths
[ 19.885779] wcd-spmi-core msm8x16_wcd_codec-ffffffc0329b9000: ASoC: mux RX3 MIX1 INP3 has no paths
[ 19.889810] init: Detected MSM SOC ID=247 SOC VER=65536 BOARD TYPE=SBC
[ 19.890244] init: failed to open ‘/sys/class/graphics/fb2/msm_fb_type’
[ 19.894968] init: property ‘persist.sys.ssr.enable_debug’ doesn’t exist while expanding ‘${persist.sys.ssr.enable_debug}’
[ 19.894984] init: cannot expand ‘${persist.sys.ssr.enable_debug}’ while writing to ‘/sys/module/subsystem_restart/parameters/enable_debug’
[ 19.895004] init: property ‘persist.sys.mba_boot_timeout’ doesn’t exist while expanding ‘${persist.sys.mba_boot_timeout}’
[ 19.895017] init: cannot expand ‘${persist.sys.mba_boot_timeout}’ while writing to ‘/sys/module/pil_msa/parameters/pbl_mba_boot_timeout_ms’
[ 19.895038] init: property ‘persist.sys.modem_auth_timeout’ doesn’t exist while expanding ‘${persist.sys.modem_auth_timeout}’
[ 19.895051] init: cannot expand ‘${persist.sys.modem_auth_timeout}’ while writing to ‘/sys/module/pil_msa/parameters/modem_auth_timeout_ms’
[ 19.895069] init: property ‘persist.sys.pil_proxy_timeout’ doesn’t exist while expanding ‘${persist.sys.pil_proxy_timeout}’
[ 19.895082] init: cannot expand ‘${persist.sys.pil_proxy_timeout}’ while writing to ‘/sys/module/peripheral_loader/parameters/proxy_timeout_ms’
[ 20.001736] wcd-spmi-core msm8x16_wcd_codec-ffffffc0329b9000: ASoC: mux RX2 MIX1 INP3 has no paths
[ 20.080399] binder: 244:244 transaction failed 29189, size 0-0
[ 20.151589] logd.auditd: start
[ 20.179745] sh (249) used greatest stack depth: 11528 bytes left
[ 20.468569] sh (250) used greatest stack depth: 11224 bytes[ 20.502926] init: cannot find ‘/system/bin/cnss_diag’, disabling ‘cnss_diag’
[ 20.514206] init: cannot find ‘/system/bin/dts_configurator’, disabling ‘dts_configurator’
shell@msm8916_64:/ $

–Starts Over–>
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.0-00261
S - IMAGE_VARIANT_STRING=HAAAANAAA
S - OEM_IMAGE_VERSION_STRING=C-BPATTH
S - Boot Config, 0x000002e1

For this problem to occur across boards is very odd. Are you using the same power supply with both boards?