Edit: My mistake. Recovery mode switch settings had to be 1-1-0.
Hello, I have Hikey960 V2. Switch settings are 1-0-1.
The board is connected to Ubuntu 18.04 via usb-c cable.
Trying to recover it as it doesn’t boot Android. But it is not recognized as usb port.
$ ll /dev/ttyUSB*
ls: cannot access ‘/dev/ttyUSB*’: No such file or directory
$ lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 413c:2107 Dell Computer Corp.
Bus 001 Device 005: ID 18d1:d00d Google Inc.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
$ dmesg
[ 634.267832] usb 1-10: new high-speed USB device number 5 using xhci_hcd
[ 634.416683] usb 1-10: New USB device found, idVendor=18d1, idProduct=d00d
[ 634.416688] usb 1-10: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 634.416692] usb 1-10: Product: HI3650
[ 634.416696] usb 1-10: Manufacturer: Fastboot2.0
[ 634.416699] usb 1-10: SerialNumber: 40151**********
$ fastboot devices
40151********** fastboot
Now I connect the board using serial interface, picocom, this is the output:
$ sudo picocom -b 115200 /dev/ttyUSB0
picocom v2.2
hikey960 boarid:5301 xloader use UART6
scsysstat_value[0].
clear reset source
last_keypoint0,reboot_type0
secdbg not DCU.
SecDbgVer exit
xloader chipid is: 0x36600110, start at 354ms.
Build Date: Sep 19 2017, 15:34:09
[clock_init] ++
hikey960 [hikey960_clk_init]
hi3660 [clk_setup]
[clock_init] –
storage type is UFS
ufs retry: 6 count v_tx:0 v_rx:0
ufs set v_tx:0 v_rx:0
Hikey960[5301] no need avs_init.
ddr ft:0xf20332a3,mode:1 target:4
UceLdOk
density: 0x08080808,0x08080808,0x08080808,0x08080808,0x08080808,0x08080808,0x08080808,0x08080808
ddr info 0x000004ff
400M
685M
1067M
C0R,V0x00000031 e:241
C0R,V0x00000032 e:66
C1R,V0x00000031 e:66
C2R,V0x00000032 e:66
C3R,V0x00000031 e:66
C0R,V0x00000033 e:66
C1R,V0x00000032 e:66
C2R,V0x00000033 e:66
C3R,V0x00000032 e:66
C0R,V0x00000034 e:66
C1R,V0x00000033 e:66
C2R,V0x00000034 e:65
C3R,V0x00000033 e:66
C0R,V0x00000031 e:66
C2R,V0x00000031 e:241
C0R,V0x00000032 e:66
C1R,V0x00000031 e:66
C2R,V0x00000032 e:66
C3R,V0x00000031 e:113
C0R,V0x00000033 e:66
C1R,V0x00000032 e:66
C2R,V0x00000033 e:66
C3R,V0x00000032 e:66
C0R,V0x00000034 e:66
C1R,V0x00000033 e:66
C2R,V0x00000034 e:65
C3R,V0x00000033 e:66
1244M
1866M
pack0Idx0Dcc:0
pack1Idx0Dcc:0
pack2Idx0Dcc:0
pack3Idx0Dcc:0
iomcu_subsys_init
boot_c0 PROFILE 4
slave0 irq0:0x00000004
slave1 irq0:0x00000004
main: ******** Fastboot for Kirin *****************
main: ******** Build Date: Jun 2 2017, 17:34:24 **
main: ******** Fastboot start at 1840 ms **********
main: print soc_id computed in xloader phase, is below:
main: 00000000 main: 00000000 main: 00000000 main: 00000000 main:
main: 00000000 main: 00000000 main: 00000000 main: 00000000 main:
led_alwayson: can’t get dtb operators
bbox: bbox_register_module_ops success.
bfm: : >>>>>enter bfm_init
bfm: : [disable_boot_fail_system] boot_fail_system state is 0
clock: PLL Stat
clock: PLL2 ctrl0=0x04909604,ctrl1=0x02000000
clock: PLL2 acpu en_stat:0x00000008, acpu gt_stat:0x00040000
clock: PLL2 final en_stat:0x00100000, final gt_stat:0x00020000
clock: PLL3 ctrl0=0x04904005,ctrl1=0x07000000
clock: PLL3 acpu en_stat:0x00000000, acpu gt_stat:0x00000000
clock: PLL3 final en_stat:0x00200000, final gt_stat:0x00040000
clock: clock init OK
ufs: ufs start on platform[36600110]ufs: ufs current mode: 0x00000011
ufs: ufs current gear: 0x00000003
ufs: ufs mphy reg 0x4A = 0x00000000
ufs: bUD0BaseOffset: 0x00000010, bUDConfigPLength: 0x00000010
ufs: UFS device manufacturerid = 0x000001ad
ufs: UFS device: H****
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02000001, mntnStageCode is 27
bfm: : <<<<<exit set_boot_stage.
storage: emmc_ops invalid
storage: storage type is UFS
bfm: : bfm system is disabled!
storage: emmc_init: BL2_STAGE_EMMC_OK is 33554435!
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02000003, mntnStageCode is 29
bfm: : <<<<>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010001, mntnStageCode is 30
bfm: : <<<<<exit set_boot_stage.
ddr: current logic version is lpddr4 verison !!!
ddr: ddr size is 4096MB
bbox: register modid [0x81fff200]
bbox: register exception succeed.
bbox: register modid [0x81fff202]
bbox: register exception succeed.
bbox: register modid [0x81fff20b]
bbox: register exception succeed.
watchdog: Enable watchdog start
boardid: [BDID]boardid: 5301
gpio: hikey960_gpio_init: GPIO 46 202 206 ouput low, GPIO 219 pullup.
load_kernel: register_update_dt_ops for usb!
secureboot: Enter secboot_init: set pll efuse flag!
secureboot: pll efuse flag has been succ set!bbox: register modid [0x81fff20a]
bbox: register exception succeed.
secureboot: SECBOOT_DEV_INFO_DADDR = 0x1d7fff00, SECBOOT_DEV_INFO_SIZE = 0x00000040!
dtimage: number of dtb = 1
dtimage: =========uncompress_dtb_addr=[0x16f00000],====vrl_addr=[0x1b0e64e0]====
dtimage: [device_tree_get_dtb_entry:215] Verify Not Exist
dtimage: fdt_init success!
dtimage: -----can not find hisilicon,fastboot node by compatible
dtimage: -----can not find hisilicon,fastboot node by compatible
load_kernel: register_update_dt_ops for led!
reboot_reason: scsysstat_value is 0x00000000
pmu: can not find fastboot,hisi-pmic-mntn node1
pmu: pmu_property_read_u32 fastboot,hisi-pmic-mntn, hisilicon,data-width, failed
pmu: pmu_mntn_record_dts_parse failed!
bbox: save_tempbuffer_to_loop_area():727:storage_read fail[-1]
reboot_reason: reboot_reason is AP_S_COLDBOOT
reboot_reason: clear_reset_source in!
reboot_reason: tmp =0x0effcc70
dtimage: -----can not find fastboot,charger node by compatible
power: get_chargerIC_type: getU32byCompatible fastboot,charger, hw_charger_type failed!
dtimage: -----can not find fastboot,coul node by compatible
power: get_coul_type: get coul_type failed!
power: get coul_type failed!
power: hi6421v500 register coulometer ops fail!
dtimage: -----can not find huawei,hisi_bci_battery node by compatible
no_module: [hi6523_get_config_info]: can’t get battery board type
dtimage: -----can not find fastboot,charger node by compatible
no_module: get hi6523 i2c reg num fail!
dtimage: -----can not find fastboot,charger node by compatible
no_module: [hi6523_start_charging_by_init_params]: get ichrg_pre_limit fail
dtimage: -----can not find huawei,hi6523_charger node by compatible
no_module: [hi6523_start_charging_by_init_params]: get reg fail
dtimage: -----can not find fastboot,buckboost node by compatible
max77813: get_buckboost_type: getU32byCompatible fastboot,buckboost, hw_buckboost_type failed!
max77813: get dts buckboost type fail!
cpu_buck: pmu type3 not registered
cpu_buck: Bad cpu buck info:1
bbox: Could not find path /rdr
bbox: Could not find status property.
mntn: tele_mntn_stat_point_init: can not bbox_ops !
dtimage: -----can not find hisilicon,fastboot node by compatible
mntn: [tele_mntn_m3_wdt_config]: getU32byCompatible(hisilicon,fastboot, lpm3-board-type) error!
mntn: mntn init
mntndump: enable_reserved_ddr_dts: Could not find path /reserved-memory/mntndump
mntndump: mntn_dump_init failed
mntndump: get_mntn_dump_addr:mid[2] is not init
mntn: kernel dump is not available
mntn: reboot_type is 0
mntn:
no need to dump_mem…
mntn: enter [registe_pstore_ramoops_dump]
mntndump: get_mntn_dump_addr:mid[5] is not init
mntn: no mdump_pstore info
mntn: M3_RDR_SYS_CONTEXT_BASE_ADDR is null
uart_cfg: [MNTN]:Could not find node.
uart_cfg: set_default_uart_cfg: uart_from_dts_read failed!
uart_cfg: module_idx 2, uart_no 6
uart_cfg: odule_idx 11, uart_no 15
uart_cfg: module_idx 2, uart_no 6
uart_cfg: getU32byCompatible(hisilicon,fastboot, uart-board-type) error!
uart_cfg: boardid: 5301 use uart port: 6
pasr: in pasr_init-43 …ddr: current logic version is lpddr4 verison !!!
ddr: current logic version is lpddr4 verison !!!
dtimage: -----can not find huawei,lcd_panel_type node by compatible
display: [display]get_detect_type: huawei,lcd_panel_type: get detect_type fail
display: lcd:no lcd detect_type
no_module: [LOGO] get_logo_buffer_from_dtsi: Could not find path /reserved-memory/logo-buffer.
no_module: [LOGO] logo_init: logo init failed!!! used the default fb addr.
display: [display]jdi_nt35696_panel_init: lcd type is not JDI_NT35696_5P5_LCD.
display: [display]jdi_otm2503b_panel_init: lcd type is not JDI_OTM2503B_5P5_LCD.
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010002, mntnStageCode is 31
bfm: : <<<<<exit set_boot_stage.
dtimage: -----can not find huawei,lcd_panel_type node by compatible
display: [display]get_dts_value: can not get huawei,lcd_panel_type, bl_bus_id=4!
dtimage: -----can not find ti,lm36923 node by compatible
display: [display]get_dts_value: can not get ti,lm36923, support=0!
display: get lm36923_support failed!
Audio_codec: [audio]:Could not find “hisilicon,codec-controller” node.
load_teeos: can not find fb node fingerprint
load_teeos: failed to find fb node ese_config
display: [display]hisi_get_disp_info: hisifb_data is NULL pointer, return!
bfm: : >>>>>enter set_boot_stage
bfm: : bootStageCode is 0x02010003, mntnStageCode is 32
bfm: : <<<<<exit set_boot_stage.
preboot: GPIO_068_SEL connect GND enter fastboot mode.
watchdog: Disable watchdog start
bfm: : [disable_boot_fail_system] boot_fail_system state is 0
rescue: ^^^^^^^^^[rescue_init] ok !
usbloader: bootmode is 4
usb: [USBFINFO]USB RESET
usb: [USBFINFO]USB CONNDONE, highspeed
usb: [USBFINFO]USB RESET
usb: [USBFINFO]USB CONNDONE, highspeed
usbloader: usb: online (highspeed)
usb: [USBFINFO]usb enum done
What did I do wrong? Is there anything I can do so I can recover the hikey960?
