Can't boot into linux after flash it through official guide

Products Support HiKey 960
#1

Hello everyone,
I’m stepping through the official guide https://www.96boards.org/documentation/consumer/hikey/hikey960/installation/linux-fastboot.md.html and everything goes fine except that I cannot finish the final booting process. Below is the tail of the UART output.

Press ESCAPE for boot options ufs: H**** device must set VS_DebugSaveConfigTime0
.[Bds]Booting Boot from SD
[Bds]Booting Grub
[Bds]Booting Android Boot
add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/e0
Loading driver at 0x000B9ADB000 EntryPoint=0x000B9ADC000 AndroidBootApp.efi
Failed to get Abootimg Size: Invalid Parameter
Failed to load boot image from boot partition: Invalid Parameter
Failed to boot from partition: Invalid Parameter
Error: Image at 000B9ADB000 start failed: Invalid Parameter
remove-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80
Image Return Status = Invalid Parameter
[Bds]Booting Android Fastboot
add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/e0
Loading driver at 0x000B9AD8000 EntryPoint=0x000B9AD9000 AndroidFastbootApp.efi
Android Fastboot mode - version 0.7.
Press RETURN or SPACE key to quit.

Anyone have any insight?
Thanks!

#2

Please check if the jumper has been set to normal boot mode:

| Auto Power up | Link 1-2 / Switch 1 | closed / ON |
| Recovery      | Link 3-4 / Switch 2 | open / OFF  |
| Fastboot      | Link 5-6 / Switch 3 | open / OFF  |
#3

Yes, I have set them to normal boot mode.

#4

Please ensure below two images have been flashed [1]:

$ sudo fastboot flash boot boot-linaro-stretch-developer-hikey-.img
$ sudo fastboot flash system rootfs-linaro-stretch-developer-hikey-.img

[1] https://snapshots.linaro.org/96boards//hikey/linaro/debian/latest/

#5

Yes, I flashed with the command in the official guide:

$ sudo fastboot flash ptable prm_ptable.img
$ sudo fastboot flash fastboot l-loader.bin
$ sudo fastboot flash fip fip.bin
$ sudo fastboot reboot-bootloader
$ sudo fastboot flash boot boot-linaro-stretch-developer-hikey-*.img
$ sudo fastboot flash system rootfs-linaro-stretch-developer-hikey-*.img
#6

Hi @leo-yan
Is it because the new 4G hynix flash on the board? I found a post which has the same issue with me https://discuss.96boards.org/t/debian-9-fails-to-boot-after-flash/5500/6.
Do you have any solutions about this issue?
Thanks for any advice!

#7 
NOTICE:  BL2: v1.5(release):v1.5-594-ge313c122
NOTICE:  BL2: Built : 09:03:15, Aug  2 2018
NOTICE:  ufs: H**** device must set VS_DebugSaveConfigTime 0x10
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v1.5(release):v1.5-594-ge313c122
NOTICE:  BL31: Built : 09:03:15, Aug  2 2018

From the log in the page you mentioned, it has different UFS model with my side. Could you confirm if this is same with you?

BTW, I suggest you could try the debug version for booting images:
https://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey960/debug/

This can give more debugging info for UEFI and if possible you could share back if have some more useful info.

#8

My hikey960 also has 4GB DDR, from the log it should not related with DDR?

#9

@leo-yan Thanks for your advice! I’ll try the debug version and share back later.

#10

@leo-yan Hi! After flashing the debug booting images, my board didn’t occur the original problem.
Then I reflashed the original booting image, it didn’t occur the problem either, which was magic…
But it still can’t finish the booting process.
Here is the serial port output. Both debug version and original version has the same problem.

     xloader chipid is: 0x36600110, start at 383ms.
    Build Date: Dec  6 2017, 15:31:59
    [clock_init] ++
    hikey960 [hikey960_clk_init]
    hi3660 [clk_setup]
    [clock_init] --
    storage type is UFS
    ufs retry: 6 count v_tx:0 v_rx:0
    ufs set v_tx:0 v_rx:0
    Hikey960[5301] no need avs_init.
    ddr ft:0xf20332a3,mode:1 target:4
    UceLdOk
    density: 0x00080008,0x00080008,0x00080008,0x00080008,0x00080008,0x00080008,0x00080008,0x00080008 
    ddr info 0x00000401 
    400M
    685M
    1067M
    C0R,V0x0000002f e:66
    C1R,V0x0000002f e:66
    C2R,V0x0000002f e:66
    C3R,V0x0000002f e:113
    C0R,V0x00000030 e:66
    C1R,V0x00000030 e:66
    C2R,V0x00000030 e:66
    C3R,V0x00000030 e:66
    C0R,V0x00000031 e:66
    C1R,V0x00000031 e:66
    C2R,V0x00000031 e:66
    C3R,V0x00000031 e:66
    C0R,V0x00000032 e:66
    C1R,V0x00000032 e:65
    C2R,V0x00000032 e:66
    C3R,V0x00000032 e:65
    C0R,V0x00000033 e:65
    C1R,V0x00000033 e:65
    C2R,V0x00000033 e:65
    C3R,V0x00000033 e:65
    C0R,V0x0000002e e:113
    C2R,V0x0000002e e:66
    C3R,V0x00000030 e:66
    C0R,V0x0000002f e:66
    C2R,V0x0000002f e:66
    C3R,V0x00000031 e:66
    C0R,V0x00000030 e:66
    C1R,V0x00000032 e:66
    C2R,V0x00000030 e:66
    C3R,V0x00000032 e:66
    C0R,V0x00000031 e:66
    C1R,V0x00000033 e:66
    C2R,V0x00000031 e:66
    C3R,V0x00000033 e:66
    C0R,V0x00000032 e:65
    C1R,V0x00000034 e:66
    C2R,V0x00000032 e:65
    C3R,V0x00000034 e:65
    1244M
    1866M
    C1R,V0x00000016 e:66
    C2R,V0x00000016 e:193
    C3R,V0x00000016 e:66
    C0R,V0x00000017 e:66
    C1R,V0x00000017 e:66
    C2R,V0x00000017 e:66
    C3R,V0x00000017 e:66
    C0R,V0x00000014 e:66
    C0R,V0x00000015 e:66
    C0R,V0x00000016 e:66
    C0R,V0x00000017 e:66
    C2R,V0x00000017 e:66
    C3R,V0x00000017 e:113
    pack0Idx0Dcc:3
    pack1Idx0Dcc:0
    pack2Idx0Dcc:0
    pack3Idx0Dcc:3
    iomcu_subsys_init
    boot_c0 PROFILE 4
    NOTICE:  BL2: v2.0(release):v2.0-227-g9c10e348
    NOTICE:  BL2: Built : 01:46:00, Nov  7 2018
    NOTICE:  ufs: H**** device must set VS_DebugSaveConfigTime 0x10
    NOTICE:  BL2: Booting BL31
    NOTICE:  BL31: v2.0(release):v2.0-227-g9c10e348
    NOTICE:  BL31: Built : 01:46:00, Nov  7 2018
    I/TC:  
    I/TC:  OP-TEE version: 3.0.0 #1 Wed Nov  7 01:45:58 UTC 2018 aarch64
    I/TC:  Initialized
    UEFI firmware (version Alpha built at 01:45:40 on Nov  7 2018)
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Core/Dxe/DxeMain/DEBUG/DxeCore.dll 0xBF18B000
    Loading DxeCore at 0x00BF18A000 EntryPoint=0x00BF18B000
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Core/Dxe/DxeMain/DEBUG/DxeCore.dll 0xBF18B000
    HOBLIST address in DXE = 0xBEF4D018
    Memory Allocation 0x00000004 0xBFFE8000 - 0xBFFE8FFF
    Memory Allocation 0x00000004 0xBFFE7000 - 0xBFFE7FFF
    Memory Allocation 0x00000004 0xBFFE6000 - 0xBFFE6FFF
    Memory Allocation 0x00000004 0xBFFE5000 - 0xBFFE5FFF
    Memory Allocation 0x00000004 0xBFFE4000 - 0xBFFE4FFF
    Memory Allocation 0x00000004 0xBFFE9000 - 0xBFFFFFFF
    Memory Allocation 0x00000004 0xBFFD4000 - 0xBFFE3FFF
    Memory Allocation 0x00000004 0xBF8CE000 - 0xBFFD3FFF
    Memory Allocation 0x00000004 0xBF1C8000 - 0xBF8CDFFF
    Memory Allocation 0x00000004 0xBF18A000 - 0xBF1C7FFF
    Memory Allocation 0x00000003 0xBF18A000 - 0xBF1C7FFF
    FV Hob            0x1AC98000 - 0x1AD87FFF
    FV Hob            0xBF1C8000 - 0xBF8CC7FF
    FV2 Hob           0xBF1C8000 - 0xBF8CC7FF
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/PCD/Dxe/Pcd/DEBUG/PcdDxe.dll 0xBF0D1000
    Loading driver at 0x000BF0D0000 EntryPoint=0x000BF0D1048 PcdDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/ArmPkg/Drivers/CpuDxe/CpuDxe/DEBUG/ArmCpuDxe.dll 0xBF0C1000
    Loading driver at 0x000BF0C0000 EntryPoint=0x000BF0C1048 ArmCpuDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Core/RuntimeDxe/RuntimeDxe/DEBUG/RuntimeDxe.dll 0xBA0D0000
    Loading driver at 0x000BA0C0000 EntryPoint=0x000BA0D0048 RuntimeDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/SecurityStubDxe/SecurityStubDxe/DEBUG/SecurityStubDxe.dll 0xBF0B0
    Loading driver at 0x000BF0B0000 EntryPoint=0x000BF0B1048 SecurityStubDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/EmbeddedPkg/EmbeddedMonotonicCounter/EmbeddedMonotonicCounter/DEBUG/EmbeddedMonotonicCo0
    Loading driver at 0x000BA020000 EntryPoint=0x000BA030048 EmbeddedMonotonicCounter.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/EmbeddedPkg/ResetRuntimeDxe/ResetRuntimeDxe/DEBUG/Reset.dll 0xB9F90000
    Loading driver at 0x000B9F80000 EntryPoint=0x000B9F90048 Reset.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/EmbeddedPkg/RealTimeClockRuntimeDxe/RealTimeClockRuntimeDxe/DEBUG/RealTimeClock.dll 0xB0
    Loading driver at 0x000B9EE0000 EntryPoint=0x000B9EF0048 RealTimeClock.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/EmbeddedPkg/MetronomeDxe/MetronomeDxe/DEBUG/MetronomeDxe.dll 0xBF0A9000
    Loading driver at 0x000BF0A8000 EntryPoint=0x000BF0A9048 MetronomeDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/SerialDxe/SerialDxe/DEBUG/SerialDxe.dll 0xBF0A1000
    Loading driver at 0x000BF0A0000 EntryPoint=0x000BF0A1048 SerialDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/OpenPlatformPkg/Platforms/Hisilicon/HiKey960/HiKey960GpioDxe/HiKey960GpioDxe/DEBUG/HiKe0
    Loading driver at 0x000BF099000 EntryPoint=0x000BF09A048 HiKey960Gpio.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061GpioDxe/DEBUG/PL061GpioDxe.dll 0xBF091000
    Loading driver at 0x000BF090000 EntryPoint=0x000BF091048 PL061GpioDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/OpenPlatformPkg/Platforms/Hisilicon/HiKey960/HiKey960Dxe/HiKey960Dxe/DEBUG/HiKey960Dxe.0
    Loading driver at 0x000BF07B000 EntryPoint=0x000BF07C048 HiKey960Dxe.efi
    [BDID]Adcin0:224
    [BDID]Adcin0Remap:1
    [BDID]Adcin1:0
    [BDID]Adcin1Remap:0
    [BDID]Adcin2:596
    [BDID]Adcin2Remap:3
    [BDID]boardid: 5301
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/Network/DpcDxe/DpcDxe/DEBUG/DpcDxe.dll 0xBF074000
    Loading driver at 0x000BF073000 EntryPoint=0x000BF074048 DpcDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/Variable/EmuRuntimeDxe/EmuVariableRuntimeDxe/DEBUG/EmuVariableRu0
    Loading driver at 0x000B9E40000 EntryPoint=0x000B9E50048 EmuVariableRuntimeDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/HiiDatabaseDxe/HiiDatabaseDxe/DEBUG/HiiDatabase.dll 0xBF043000
    Loading driver at 0x000BF042000 EntryPoint=0x000BF043048 HiiDatabase.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/DevicePathDxe/DevicePathDxe/DEBUG/DevicePathDxe.dll 0xBF02E000
    Loading driver at 0x000BF02D000 EntryPoint=0x000BF02E048 DevicePathDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/CapsuleRuntimeDxe/CapsuleRuntimeDxe/DEBUG/CapsuleRuntimeDxe.dll 0
    Loading driver at 0x000B9DA0000 EntryPoint=0x000B9DB0048 CapsuleRuntimeDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/ArmPkg/Drivers/ArmGic/ArmGicDxe/DEBUG/ArmGicDxe.dll 0xBF024000
    Loading driver at 0x000BF023000 EntryPoint=0x000BF024048 ArmGicDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/FaultTolerantWriteDxe/FaultTolerantWriteDxe/DEBUG/FaultTolerantW0
    Loading driver at 0x000BF014000 EntryPoint=0x000BF015048 FaultTolerantWriteDxe.efi
    Ftw: Workspace or Spare block does not exist!
    Error: Image at 000BF014000 start failed: Invalid Parameter
    remove-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/FaultTolerantWriteDxe/FaultTolerantWriteDxe/DEBUG/FaultTolera0
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/SetupBrowserDxe/SetupBrowserDxe/DEBUG/SetupBrowser.dll 0xBEFF8000
    Loading driver at 0x000BEFF7000 EntryPoint=0x000BEFF8048 SetupBrowser.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/BdsDxe/BdsDxe/DEBUG/BdsDxe.dll 0xBEFCD000
    Loading driver at 0x000BEFCC000 EntryPoint=0x000BEFCD048 BdsDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/EmbeddedPkg/Drivers/DtPlatformDxe/DtPlatformDxe/DEBUG/DtPlatformDxe.dll 0xBEFC3000
    Loading driver at 0x000BEFC2000 EntryPoint=0x000BEFC3048 DtPlatformDxe.efi
    DtPlatformDxeEntryPoint: no DT/ACPI preference found, defaulting to DT
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/ArmPkg/Drivers/TimerDxe/TimerDxe/DEBUG/ArmTimerDxe.dll 0xBEFBA000
    Loading driver at 0x000BEFB9000 EntryPoint=0x000BEFBA048 ArmTimerDxe.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/DisplayEngineDxe/DisplayEngineDxe/DEBUG/DisplayEngine.dll 0xBEF90
    Loading driver at 0x000BEF96000 EntryPoint=0x000BEF97048 DisplayEngine.efi
    add-symbol-file /home/buildslave/workspace/96boards-reference-uefi-staging/80/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/WatchdogTimerDxe/WatchdogTimer/DEBUG/WatchdogTimer.dll 0xBEF8F000
    Loading driver at 0x000BEF8E000 EntryPoint=0x000BEF8F048 WatchdogTimer.efi
    Loading Linux 4.15-hikey ...
    Loading initial ramdisk ...
    Loading driver at 0x000B7264000 EntryPoint=0x000B818875C
    Loading driver at 0x000B7264000 EntryPoint=0x000B818875C 
    EFI stub: Booting Linux Kernel...
    EFI stub: Using DTB from configuration table
    EFI stub: Exiting boot services and installing virtual address map...
    I/TC:  Dynamic shared memory is enabled
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
        [    0.000000] Linux version 4.15-hikey (abuild@r2-a19) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 SMP PREEMPT Sun Jul 15 12:43:38 UTC 2018
        [    0.000000] Machine model: HiKey960
        [    0.000000] efi: Getting EFI parameters from FDT:
        [    0.000000] efi: EFI v2.60 by EDK II
        [    0.000000] efi:  MEMATTR=0xbde6c018 
        [    0.000000] cma: Reserved 16 MiB at 0x00000000df000000
        [    0.000000] NUMA: No NUMA configuration found
        [    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000021fffffff]
        [    0.000000] NUMA: NODE_DATA [mem 0x21ffbf100-0x21ffc0bff]
        [    0.000000] Zone ranges:
        [    0.000000]   DMA      [mem 0x0000000000000000-0x00000000ffffffff]
        [    0.000000]   Normal   [mem 0x0000000100000000-0x000000021fffffff]
        [    0.000000] Movable zone start for each node
        [    0.000000] Early memory node ranges
        [    0.000000]   node   0: [mem 0x0000000000000000-0x000000001abfffff]
        [    0.000000]   node   0: [mem 0x000000001ad88000-0x0000000031ffffff]
        [    0.000000]   node   0: [mem 0x0000000032101000-0x000000003dffffff]
        [    0.000000]   node   0: [mem 0x0000000040000000-0x0000000089b7ffff]
        [    0.000000]   node   0: [mem 0x0000000089cc0000-0x00000000b9baffff]
        [    0.000000]   node   0: [mem 0x00000000b9bb0000-0x00000000b9c4ffff]
        [    0.000000]   node   0: [mem 0x00000000b9c50000-0x00000000b9d4ffff]
        [    0.000000]   node   0: [mem 0x00000000b9d50000-0x00000000ba113fff]
        [    0.000000]   node   0: [mem 0x00000000ba114000-0x00000000bf12ffff]
        [    0.000000]   node   0: [mem 0x00000000bf130000-0x00000000bf17ffff]
        [    0.000000]   node   0: [mem 0x00000000bf180000-0x00000000dfffffff]
        [    0.000000]   node   0: [mem 0x0000000200000000-0x000000021fffffff]
        [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000021fffffff]
        [    0.000000] psci: probing for conduit method from DT.
        [    0.000000] psci: PSCIv1.1 detected in firmware.
        [    0.000000] psci: Using standard PSCI v0.2 function IDs
        [    0.000000] psci: Trusted OS migration not required
        [    0.000000] random: fast init done
        [    0.000000] percpu: Embedded 23 pages/cpu @        (ptrval) s55320 r8192 d30696 u94208
        [    0.000000] Detected VIPT I-cache on CPU0
        [    0.000000] CPU features: enabling workaround for ARM erratum 845719
        [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1023174
        [    0.000000] Policy zone: Normal
        [    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.15-hikey root=UUID=4be2a8aa-b08f-4446-a223-f77e31460c8e ro
        [    0.000000] software IO TLB [mem 0xdafff000-0xdefff000] (64MB) mapped at [        (ptrval)-        (ptrval)]
        [    0.000000] Memory: 3962924K/4157660K available (10428K kernel code, 1560K rwdata, 4984K rodata, 1152K init, 424K bss, 178352K reserved, 16384K cma-reserved)
        [    0.000000] Virtual kernel memory layout:
        [    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
        [    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
        [    0.000000]       .text : 0x        (ptrval) - 0x        (ptrval)   ( 10432 KB)
        [    0.000000]     .rodata : 0x        (ptrval) - 0x        (ptrval)   (  5056 KB)
        [    0.000000]       .init : 0x        (ptrval) - 0x        (ptrval)   (  1152 KB)
        [    0.000000]       .data : 0x        (ptrval) - 0x        (ptrval)   (  1561 KB)
        [    0.000000]        .bss : 0x        (ptrval) - 0x        (ptrval)   (   425 KB)
        [    0.000000]     fixed   : 0xffff7dfffe7fb000 - 0xffff7dfffec00000   (  4116 KB)
        [    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
        [    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
        [    0.000000]               0xffff7e0000000000 - 0xffff7e0008800000   (   136 MB actual)
        [    0.000000]     memory  : 0xffff800000000000 - 0xffff800220000000   (  8704 MB)
        [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
        [    0.000000] Preemptible hierarchical RCU implementation.
        [    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8.
        [    0.000000]  Tasks RCU enabled.
        [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
        [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
        [    0.000000] GIC: Using split EOI/Deactivate mode
        [    0.000000] arch_timer: cp15 timer(s) running at 1.92MHz (phys).
        [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1c570327e, max_idle_ns: 1763180809505 ns
        [    0.000005] sched_clock: 56 bits at 1920kHz, resolution 520ns, wraps every 4398046510977ns
        [    0.000090] clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58334160866034 ns
        [    0.000441] Console: colour dummy device 80x25
        [    0.000819] console [tty0] enabled
        [    0.000894] Calibrating delay loop (skipped), value calculated using timer frequency.. 3.84 BogoMIPS (lpj=7680)
        [    0.000911] pid_max: default: 32768 minimum: 301
        [    0.000976] Security Framework initialized
        [    0.002130] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
        [    0.002733] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
        [    0.002774] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
        [    0.002801] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
        [    0.020068] ASID allocator initialised with 65536 entries
        [    0.028044] Hierarchical SRCU implementation.
        [    0.039262] Remapping and enabling EFI services.
        [    0.039353]   EFI remap 0x00000000b9bb0000 =>         (ptrval)
        [    0.039368]   EFI remap 0x00000000b9c00000 =>         (ptrval)
        [    0.039383]   EFI remap 0x00000000b9d50000 =>         (ptrval)
        [    0.039397]   EFI remap 0x00000000b9da0000 =>         (ptrval)
        [    0.039411]   EFI remap 0x00000000b9df0000 =>         (ptrval)
        [    0.039426]   EFI remap 0x00000000b9e40000 =>         (ptrval)
        [    0.039443]   EFI remap 0x00000000b9e90000 =>         (ptrval)
        [    0.039457]   EFI remap 0x00000000b9ee0000 =>         (ptrval)
        [    0.039472]   EFI remap 0x00000000b9f30000 =>         (ptrval)
        [    0.039486]   EFI remap 0x00000000b9f80000 =>         (ptrval)
        [    0.039501]   EFI remap 0x00000000b9fd0000 =>         (ptrval)
        [    0.039516]   EFI remap 0x00000000ba020000 =>         (ptrval)
        [    0.039541]   EFI remap 0x00000000ba070000 =>         (ptrval)
        [    0.039556]   EFI remap 0x00000000ba0c0000 =>         (ptrval)
        [    0.039571]   EFI remap 0x00000000bf130000 =>         (ptrval)
        [    0.039580]   EFI remap 0x00000000fff05000 =>         (ptrval)

The message is too long to write in a reply, continued in the next reply…
Thanks!

P.S. I added an extra command after flashing rootfs:
sudo fastboot reboot
I don’t know if it’s related.

#11 
    [    0.048125] smp: Bringing up secondary CPUs ...
    [    0.076515] Detected VIPT I-cache on CPU1
    [    0.076599] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
    [    0.104476] Detected VIPT I-cache on CPU2
    [    0.104502] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
    [    0.132493] Detected VIPT I-cache on CPU3
    [    0.132511] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
    [    0.162061] CPU features: enabling workaround for ARM erratum 858921
    [    0.162066] Detected VIPT I-cache on CPU4
    [    0.162074] CPU features: SANITY CHECK: Unexpected variation in SYS_ID_AA64MMFR0_EL1. Boot CPU: 0x00000000001122, CPU4: 0x00000000101122
    [    0.162080] CPU features: Unsupported CPU feature variation detected.
    [    0.162175] arch_timer: Enabling local workaround for ARM erratum 858921
    [    0.162183] arch_timer: CPU4: Trapping CNTVCT access
    [    0.162188] CPU4: Booted secondary processor 0x0000000100 [0x410fd091]
    [    0.188500] Detected VIPT I-cache on CPU5
    [    0.188505] CPU features: SANITY CHECK: Unexpected variation in SYS_ID_AA64MMFR0_EL1. Boot CPU: 0x00000000001122, CPU5: 0x00000000101122
    [    0.188515] arch_timer: Enabling local workaround for ARM erratum 858921
    [    0.188519] arch_timer: CPU5: Trapping CNTVCT access
    [    0.188523] CPU5: Booted secondary processor 0x0000000101 [0x410fd091]
    [    0.216524] Detected VIPT I-cache on CPU6
    [    0.216530] CPU features: SANITY CHECK: Unexpected variation in SYS_ID_AA64MMFR0_EL1. Boot CPU: 0x00000000001122, CPU6: 0x00000000101122
    [    0.216539] arch_timer: Enabling local workaround for ARM erratum 858921
    [    0.216544] arch_timer: CPU6: Trapping CNTVCT access
    [    0.216547] CPU6: Booted secondary processor 0x0000000102 [0x410fd091]
    [    0.244553] Detected VIPT I-cache on CPU7
    [    0.244557] CPU features: SANITY CHECK: Unexpected variation in SYS_ID_AA64MMFR0_EL1. Boot CPU: 0x00000000001122, CPU7: 0x00000000101122
    [    0.244566] arch_timer: Enabling local workaround for ARM erratum 858921
    [    0.244571] arch_timer: CPU7: Trapping CNTVCT access
    [    0.244574] CPU7: Booted secondary processor 0x0000000103 [0x410fd091]
    [    0.244626] smp: Brought up 1 node, 8 CPUs
    [    0.244805] SMP: Total of 8 processors activated.
    [    0.244814] CPU features: detected feature: 32-bit EL0 Support
    [    0.245123] CPU: All CPU(s) started at EL2
    [    0.245156] alternatives: patching kernel code
    [    0.246065] devtmpfs: initialized
    [    0.249610] Registered cp15_barrier emulation handler
    [    0.249636] Registered setend emulation handler
    [    0.249838] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
    [    0.249897] futex hash table entries: 2048 (order: 6, 262144 bytes)
    [    0.250422] pinctrl core: initialized pinctrl subsystem
    [    0.251394] DMI not present or invalid.
    [    0.251677] NET: Registered protocol family 16
    [    0.251989] audit: initializing netlink subsys (disabled)
    [    0.252096] audit: type=2000 audit(0.248:1): state=initialized audit_enabled=0 res=1
    [    0.252938] cpuidle: using governor menu
    [    0.253423] vdso: 2 pages (1 code @ 0000000079db5adb, 1 data @ 00000000fc76d052)
    [    0.253443] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
    [    0.254148] DMA: preallocated 256 KiB pool for atomic allocations
    [    0.254808] Serial: AMBA PL011 UART driver
    [    0.276540] uart-pl011 ffd74000.serial: could not find pctldev for node /soc/pinmux@e896c000/uart3_pmx_func, deferring probe
    [    0.276679] uart-pl011 fdf01000.serial: could not find pctldev for node /soc/pinmux@e896c000/uart4_pmx_func, deferring probe
    [    0.276795] uart-pl011 fff32000.serial: could not find pctldev for node /soc/pinmux@e896c000/uart6_pmx_func, deferring probe
    [    0.287539] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
    [    0.288339] ACPI: Interpreter disabled.
    [    0.289064] vgaarb: loaded
    [    0.289255] SCSI subsystem initialized
    [    0.289451] ssp-pl022 ffd68000.spi: could not find pctldev for node /soc/pinmux@fff11000/spi2_pmx_func, deferring probe
    [    0.289483] ssp-pl022 ff3b3000.spi: could not find pctldev for node /soc/pinmux@ff3b6000/spi3_pmx_func, deferring probe
    [    0.289670] usbcore: registered new interface driver usbfs
    [    0.289707] usbcore: registered new interface driver hub
    [    0.289767] usbcore: registered new device driver usb
    [    0.289958] i2c_designware ffd71000.i2c: could not find pctldev for node /soc/pinmux@fff11000/i2c0_pmx_func, deferring probe
    [    0.289987] i2c_designware ffd72000.i2c: could not find pctldev for node /soc/pinmux@fff11000/i2c1_pmx_func, deferring probe
    [    0.290013] i2c_designware fdf0b000.i2c: could not find pctldev for node /soc/pinmux@fff11000/i2c7_pmx_func, deferring probe
    [    0.290323] pps_core: LinuxPPS API ver. 1 registered
    [    0.290331] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.290352] PTP clock support registered
    [    0.290431] EDAC MC: Ver: 3.0.0
    [    0.290607] dmi: Firmware registration failed.
    [    0.290680] Registered efivars operations
    [    0.291470] Advanced Linux Sound Architecture Driver Initialized.
    [    0.292149] clocksource: Switched to clocksource arch_sys_counter
    [    0.292290] VFS: Disk quotas dquot_6.6.0
    [    0.292336] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [    0.292493] pnp: PnP ACPI: disabled
    [    0.296048] NET: Registered protocol family 2
    [    0.296521] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
    [    0.296717] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
    [    0.297114] TCP: Hash tables configured (established 32768 bind 32768)
    [    0.297232] UDP hash table entries: 2048 (order: 4, 65536 bytes)
    [    0.297297] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
    [    0.297485] NET: Registered protocol family 1
    [    0.297797] RPC: Registered named UNIX socket transport module.
    [    0.297806] RPC: Registered udp transport module.
    [    0.297812] RPC: Registered tcp transport module.
    [    0.297819] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.297966] Unpacking initramfs...
    [    0.402565] Freeing initrd memory: 3936K
    [    0.403340] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
    [    0.403582] hw perfevents: enabled with armv8_cortex_a73 PMU driver, 7 counters available
    [    0.403786] kvm [1]: 8-bit VMID
    [    0.403793] kvm [1]: IDMAP page: a9b000
    [    0.403799] kvm [1]: HYP VA range: 800000000000:ffffffffffff
    [    0.404699] kvm [1]: vgic-v2@e82b4000
    [    0.404793] kvm [1]: vgic interrupt IRQ1
    [    0.404810] kvm [1]: virtual timer IRQ4
    [    0.404912] kvm [1]: Hyp mode initialized successfully
    [    0.407417] Initialise system trusted keyrings
    [    0.407521] workingset: timestamp_bits=44 max_order=20 bucket_order=0
    [    0.411282] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.411675] NFS: Registering the id_resolver key type
    [    0.411704] Key type id_resolver registered
    [    0.411710] Key type id_legacy registered
    [    0.411722] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
    [    0.411857] 9p: Installing v9fs 9p2000 file system support
    [    0.413271] Key type asymmetric registered
    [    0.413287] Asymmetric key parser 'x509' registered
    [    0.413398] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
    [    0.413491] io scheduler noop registered
    [    0.413610] io scheduler cfq registered (default)
    [    0.413619] io scheduler mq-deadline registered
    [    0.413626] io scheduler kyber registered
    [    0.415632] pinctrl-single e896c000.pinmux: 124 pins at pa 00000000ecf4b3e1 size 496
    [    0.415835] pinctrl-single ff37e000.pinmux: 6 pins at pa 000000004f3a6122 size 24
    [    0.415931] pinctrl-single ff3b6000.pinmux: 12 pins at pa 00000000d495058a size 48
    [    0.416033] pinctrl-single ff3fd000.pinmux: 6 pins at pa 00000000ee2299ff size 24
    [    0.416170] pinctrl-single fff11000.pinmux: 42 pins at pa 0000000032dc98f3 size 168
    [    0.416358] pinctrl-single e896c800.pinmux: 128 pins at pa 000000005e286955 size 512
    [    0.416440] pinctrl-single ff3b6800.pinmux: 6 pins at pa 00000000cdc0a822 size 24
    [    0.416536] pinctrl-single ff3fd800.pinmux: 6 pins at pa 000000008c9a1d82 size 24
    [    0.416617] pinctrl-single ff37e800.pinmux: 6 pins at pa 00000000e82743bb size 24
    [    0.416740] pinctrl-single fff11800.pinmux: 47 pins at pa 00000000e80731c3 size 188
    [    0.417948] pl061_gpio e8a0b000.gpio: PL061 GPIO chip @0x00000000e8a0b000 registered
    [    0.418110] pl061_gpio e8a0c000.gpio: PL061 GPIO chip @0x00000000e8a0c000 registered
    [    0.418265] pl061_gpio e8a0d000.gpio: PL061 GPIO chip @0x00000000e8a0d000 registered
    [    0.418407] pl061_gpio e8a0e000.gpio: PL061 GPIO chip @0x00000000e8a0e000 registered
    [    0.418554] pl061_gpio e8a0f000.gpio: PL061 GPIO chip @0x00000000e8a0f000 registered
    [    0.418709] pl061_gpio e8a10000.gpio: PL061 GPIO chip @0x00000000e8a10000 registered
    [    0.418854] pl061_gpio e8a11000.gpio: PL061 GPIO chip @0x00000000e8a11000 registered
    [    0.419007] pl061_gpio e8a12000.gpio: PL061 GPIO chip @0x00000000e8a12000 registered
    [    0.419149] pl061_gpio e8a13000.gpio: PL061 GPIO chip @0x00000000e8a13000 registered
    [    0.419312] pl061_gpio e8a14000.gpio: PL061 GPIO chip @0x00000000e8a14000 registered
    [    0.419468] pl061_gpio e8a15000.gpio: PL061 GPIO chip @0x00000000e8a15000 registered
    [    0.419615] pl061_gpio e8a16000.gpio: PL061 GPIO chip @0x00000000e8a16000 registered
    [    0.419779] pl061_gpio e8a17000.gpio: PL061 GPIO chip @0x00000000e8a17000 registered
    [    0.419934] pl061_gpio e8a18000.gpio: PL061 GPIO chip @0x00000000e8a18000 registered
    [    0.420085] pl061_gpio e8a19000.gpio: PL061 GPIO chip @0x00000000e8a19000 registered
    [    0.420268] pl061_gpio e8a1a000.gpio: PL061 GPIO chip @0x00000000e8a1a000 registered
    [    0.420424] pl061_gpio e8a1b000.gpio: PL061 GPIO chip @0x00000000e8a1b000 registered
    [    0.420584] pl061_gpio e8a1c000.gpio: PL061 GPIO chip @0x00000000e8a1c000 registered
    [    0.420772] pl061_gpio ff3b4000.gpio: PL061 GPIO chip @0x00000000ff3b4000 registered
    [    0.420924] pl061_gpio ff3b5000.gpio: PL061 GPIO chip @0x00000000ff3b5000 registered
    [    0.421095] pl061_gpio e8a1f000.gpio: PL061 GPIO chip @0x00000000e8a1f000 registered
    [    0.421246] pl061_gpio e8a20000.gpio: PL061 GPIO chip @0x00000000e8a20000 registered
    [    0.421419] pl061_gpio fff0b000.gpio: PL061 GPIO chip @0x00000000fff0b000 registered
    [    0.421594] pl061_gpio fff0c000.gpio: PL061 GPIO chip @0x00000000fff0c000 registered
    [    0.421757] pl061_gpio fff0d000.gpio: PL061 GPIO chip @0x00000000fff0d000 registered
    [    0.421927] pl061_gpio fff0e000.gpio: PL061 GPIO chip @0x00000000fff0e000 registered
    [    0.422094] pl061_gpio fff0f000.gpio: PL061 GPIO chip @0x00000000fff0f000 registered
    [    0.422266] pl061_gpio fff10000.gpio: PL061 GPIO chip @0x00000000fff10000 registered
    [    0.422424] pl061_gpio fff1d000.gpio: PL061 GPIO chip @0x00000000fff1d000 registered
    [    0.426541] k3-dma fdf30000.dma: initialized
    [    0.429898] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    [    0.431211] SuperH (H)SCI(F) driver initialized
    [    0.431432] msm_serial: driver initialized
    [    0.436941] loop: module loaded
    [    0.439099] ufshcd-hisi ff3b0000.ufs: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled
    [    0.439130] ufshcd-hisi ff3b0000.ufs: ufshcd_populate_vreg: Unable to find vcc-supply regulator, assuming enabled
    [    0.439142] ufshcd-hisi ff3b0000.ufs: ufshcd_populate_vreg: Unable to find vccq-supply regulator, assuming enabled
    [    0.439154] ufshcd-hisi ff3b0000.ufs: ufshcd_populate_vreg: Unable to find vccq2-supply regulator, assuming enabled
    [    0.468656] scsi host0: ufshcd
    [    0.482282] libphy: Fixed MDIO Bus: probed
    [    0.482517] tun: Universal TUN/TAP device driver, 1.6
    [    0.483067] thunder-xcv, ver 1.0
    [    0.483106] thunder-BGX, ver 1.0
    [    0.483134] thunder-nic, ver 1.0
    [    0.483308] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
    [    0.483316] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
    [    0.483350] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
    [    0.483358] igb: Copyright (c) 2007-2014 Intel Corporation.
    [    0.483385] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
    [    0.483394] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
    [    0.483567] sky2: driver version 1.30
    [    0.483772] usbcore: registered new interface driver asix
    [    0.483832] usbcore: registered new interface driver ax88179_178a
    [    0.483952] VFIO - User Level meta-driver version: 0.3
    [    0.484716] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    0.484754] ehci-pci: EHCI PCI platform driver
    [    0.484788] ehci-platform: EHCI generic platform driver
    [    0.484868] ehci-orion: EHCI orion driver
    [    0.484924] ehci-exynos: EHCI EXYNOS driver
    [    0.484980] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [    0.485002] ohci-pci: OHCI PCI platform driver
    [    0.485035] ohci-platform: OHCI generic platform driver
    [    0.485098] ohci-exynos: OHCI EXYNOS driver
    [    0.485371] usbcore: registered new interface driver usb-storage
    [    0.485441] usbcore: registered new interface driver usbserial_generic
    [    0.485470] usbserial: USB Serial support registered for generic
    [    0.487123] rtc-efi rtc-efi: rtc core: registered rtc-efi as rtc0
    [    0.487496] rtc-pl031 fff04000.rtc: rtc core: registered pl031 as rtc1
    [    0.487904] i2c /dev entries driver
    [    0.491260] sdhci: Secure Digital Host Controller Interface driver
    [    0.491286] sdhci: Copyright(c) Pierre Ossman
    [    0.491409] Synopsys Designware Multimedia Card Interface Driver
    [    0.491883] dwmmc_k3 ff37f000.dwmmc1: fifo-depth property not found, using value of FIFOTH register as default
    [    0.494142] dwmmc_k3 ff37f000.dwmmc1: IDMAC supports 64-bit address mode.
    [    0.494282] dwmmc_k3 ff37f000.dwmmc1: Using internal DMA controller.
    [    0.494296] dwmmc_k3 ff37f000.dwmmc1: Version ID is 270a
    [    0.494343] dwmmc_k3 ff37f000.dwmmc1: DW MMC controller at irq 59,32 bit host data width,256 deep fifo
    [    0.494533] dwmmc_k3 ff37f000.dwmmc1: Got CD GPIO
    [    0.514611] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
    [    0.534609] dwmmc_k3 ff3ff000.dwmmc2: fifo-depth property not found, using value of FIFOTH register as default
    [    0.536756] dwmmc_k3 ff3ff000.dwmmc2: IDMAC supports 64-bit address mode.
    [    0.536875] dwmmc_k3 ff3ff000.dwmmc2: Using internal DMA controller.
    [    0.536888] dwmmc_k3 ff3ff000.dwmmc2: Version ID is 270a
    [    0.536924] dwmmc_k3 ff3ff000.dwmmc2: DW MMC controller at irq 60,32 bit host data width,256 deep fifo
    [    0.537528] sdhci-pltfm: SDHCI platform and OF driver helper
    [    0.539756] ledtrig-cpu: registered to indicate activity on CPUs
    [    0.540802] usbcore: registered new interface driver usbhid
    [    0.540824] usbhid: USB HID core driver
    [    0.541601] optee: probing for conduit method from DT.
    [    0.545572] optee: initialized driver
    [    0.545990] usbcore: registered new interface driver snd-usb-audio
    [    0.547226] NET: Registered protocol family 10
    [    0.548000] Segment Routing with IPv6
    [    0.548049] NET: Registered protocol family 17
    [    0.548102] 9pnet: Installing 9P2000 support
    [    0.548189] Key type dns_resolver registered
    [    0.548638] registered taskstats version 1
    [    0.548647] Loading compiled-in X.509 certificates
    [    0.553497] ffd74000.serial: ttyAMA3 at MMIO 0xffd74000 (irq = 21, base_baud = 0) is a PL011 rev2
    [    0.554044] fdf01000.serial: ttyAMA4 at MMIO 0xfdf01000 (irq = 22, base_baud = 0) is a PL011 rev2
    [    0.554147] serial serial0: tty port ttyAMA4 registered
    [    0.554335] fff32000.serial: ttyAMA6 at MMIO 0xfff32000 (irq = 23, base_baud = 0) is a PL011 rev2
    [    0.602505] ufshcd-hisi ff3b0000.ufs: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0
    [    0.738397] ufs final power mode: gear = 3, lane = 2, pwr = 1, rate = 2
    [    0.740838] ufshcd-hisi ff3b0000.ufs: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
    [    2.245457] ufshcd-hisi ff3b0000.ufs: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
    [    2.560340] console [ttyAMA6] enabled
    [    2.565090] ssp-pl022 ffd68000.spi: ARM PL022 driver, device ID: 0x00041022
    [    2.572197] ssp-pl022 ffd68000.spi: mapped registers from 0x00000000ffd68000 to 00000000ab319652
    [    2.581067] ssp-pl022 ffd68000.spi: setup for DMA on RX dma0chan0, TX dma0chan1
    [    2.589422] ssp-pl022 ff3b3000.spi: ARM PL022 driver, device ID: 0x00041022
    [    2.596498] ssp-pl022 ff3b3000.spi: mapped registers from 0x00000000ff3b3000 to 000000005910556c
    [    2.605333] ssp-pl022 ff3b3000.spi: setup for DMA on RX dma0chan2, TX dma0chan3
    [    2.618706] dwmmc_k3 ff3ff000.dwmmc2: fifo-depth property not found, using value of FIFOTH register as default
    [    2.630884] dwmmc_k3 ff3ff000.dwmmc2: IDMAC supports 64-bit address mode.
    [    2.637804] dwmmc_k3 ff3ff000.dwmmc2: Using internal DMA controller.
    [    2.644168] dwmmc_k3 ff3ff000.dwmmc2: Version ID is 270a
    [    2.649510] dwmmc_k3 ff3ff000.dwmmc2: DW MMC controller at irq 60,32 bit host data width,128 deep fifo
    [    2.658967] mmc_host mmc1: card is non-removable.
    [    2.762421] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
    [    2.789728] input: keys as /devices/platform/keys/input/input0
    [    2.796240] dwmmc_k3 ff3ff000.dwmmc2: card claims to support voltages below defined range
    [    2.804438] rtc-efi rtc-efi: setting system clock to 1970-01-01 00:01:31 UTC (91)
    [    2.815366] ALSA device list:
    [    2.817001] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0)
    [    2.818410] mmc1: new SDIO card at address 0001
    [    2.832643]   No soundcards found.
    [    2.836378] uart-pl011 fff32000.serial: no DMA platform data
    [    3.749450] ufshcd-hisi ff3b0000.ufs: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
    [    5.285443] ufshcd-hisi ff3b0000.ufs: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
    [    5.294846] ufshcd-hisi ff3b0000.ufs: ufshcd_query_flag_retry: query attribute, opcode 5, idn 3, failed with error -11 after 3 retires
    [    6.821414] ufshcd-hisi ff3b0000.ufs: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
    [    8.357444] ufshcd-hisi ff3b0000.ufs: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
    [    9.893432] ufshcd-hisi ff3b0000.ufs: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
    [    9.903704] ufshcd-hisi ff3b0000.ufs: ufshcd_read_desc_param: Failed reading descriptor. desc_id 8, desc_index 0, param_offset 0, ret -11
    [    9.916059] ufshcd-hisi ff3b0000.ufs: ufshcd_init_icc_levels: Failed reading power descriptor.len = 98 ret = -11
    [   31.015704] ufshcd-hisi ff3b0000.ufs: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0
    [   31.028808] ufshcd-hisi ff3b0000.ufs: UPIU[0] - issue time 9922348 us
    [   31.035248] ufshcd-hisi ff3b0000.ufs: UPIU[0] - complete time 0 us
    [   31.041427] ufshcd-hisi ff3b0000.ufs: UPIU[0] - Transfer Request Descriptor phys@0xdf058000
    [   31.049783] UPIU TRD: 00000000: 15000000 00000000 0000000f 00000000
    [   31.056049] UPIU TRD: 00000010: df040000 00000000 00800080 01000001
    [   31.062314] ufshcd-hisi ff3b0000.ufs: UPIU[0] - Request UPIU phys@0xdf040000
    [   31.069362] UPIU REQ: 00000000: 00d04001 00000000 00000000 24000000
    [   31.075627] UPIU REQ: 00000010: 00000012 00000024 00000000 00000000
    [   31.081892] ufshcd-hisi ff3b0000.ufs: UPIU[0] - Response UPIU phys@0xdf040200
    [   31.089026] UPIU RSP: 00000000: 00000000 00000000 00000000 00000000
    [   31.095291] UPIU RSP: 00000010: 00000000 00000000 00000000 00000000
    [   31.101557] UPIU RSP: 00000020: 00000000 00000000 00000000 00000000
    [   31.107820] UPIU RSP: 00000030: 00000000
    [   31.111740] ufshcd-hisi ff3b0000.ufs: UPIU[0] - PRDT - 1 entries  phys@0xdf040400
    [   31.119223] UPIU PRDT: 00000000: 185e3000 00000002 00000000 00000023
    [   31.261921] ufs final power mode: gear = 3, lane = 2, pwr = 1, rate = 2
    [   31.270989] ufshcd-hisi ff3b0000.ufs: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
    [   31.283550] Freeing unused kernel memory: 1152K
    Loading, please wait...
    starting version 232
    Begin: Loading essential drivers ... done.
    Begin: Running /scripts/init-premount ... done.
    Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
    Begin: Running /scripts/local-premount ... done.
    Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    [   47.524388] random: crng init done
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    Begin: Running /scripts/local-block ... done.
    done.
    Gave up waiting for root file system device.  Common problems:
     - Boot args (cat /proc/cmdline)
       - Check rootdelay= (did the system wait long enough?)
     - Missing modules (cat /proc/modules; ls /dev)
    ALERT!  UUID=4be2a8aa-b08f-4446-a223-f77e31460c8e does not exist.  Dropping to a shell!
    (initramfs)
#12

This is definitely the error with rootfs, the uuid is defined for rootfs partition. So are you using this ptable [1]?

[1] https://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey960/debug/prm_ptable.img

#13

@favoryoung From logs you have provided, it seems that Debian kernel UFS driver fails to detect hynix UFS flash. That could be the reason that it fails to mount rootfs partition. As @leo-yan mentioned in one of other post on the forum regarding an issue with hynix UFS chip as:

So I would rather suggest you to boot Debian via SD using following steps:

  1. Download SD card image as pointed here [1].
  2. Follow hikey SD card installation guide [2], it works for me on hikey960 too.

[1] Debian Downloads for HiKey960 - 96Boards
[2] Create a Bootable SD Card for HiKey - 96Boards

1 Like
#14

Yes, I’m using this ptable.

#15

That could be likely to solve my problem. I’ll try it.
Thanks!

#16

It boots! Thanks!
But it’s such a waste not using the 32G flash. It’s better to have a kernel that applies that Hynix patch. I’ll try to build one as the below post.